Available BF-Series Exterior Power Vent Systems:
Available Exhausto Exterior Power Vent Systems:
Page 8
Installation
Installing ST Terminations with Frame
1. Frame the termination opening to 22" x 22".
2. Fasten the termination and its frame using a minimum of 4
screws. (See Figure 8, 8a)
Exterior Power Vent Installation
Installation Requirements for Exterior Power Venter
The CVIEW-PRC fireplaces are certified for use with any approved
UL certified B-Vent venting components. (Use of other non-certified parts will
void the Montigo warranty, and may impede the operation of the fireplace).
The clearance for B-Vents is listed by the manufacturer of the B-Vent. In-
stall components and fittings using the clearances specified by the B-Vent
manufacturer .
All joints must be secured as per the instructions provided by the B-Vent
manufacturer.
The exhaust portion of a vent termination must not be recessed in a wall
cavity.
Horizontal runs must be supported by a minimum of three supports per 10
feet of venting.
Vent Terminations
Selecting A Termination Location
Before installing the termination or venting, check to ensure the
planned termination location is acceptable. See figure 10, 10a below.
Exterior Power Vent / Wire
Routing Installation Diagram
Figure 7a. C-View Control Box / Power Vent Wire Routing Diagram
For vertical installations the longest vent run is 140 feet with a limit of 8 -90°
Elbows, or 16 - 45° Elbows. For longer runs contact the C-View Manufac-
turer.
For horizontal installations the longest vent run is 100 feet with a limit of 4
-90° Elbows, or 8 - 45° Elbows. For longer runs contact the C-View Manu-
facturer.
It is important that the location of the power vent motor is not exposed to a
downfall of water not in excess of the standard rain fall.
For Exterior Power Vent Installations use EXPVRN10 or EXPVRN12 or for
extra long vent runs use BF52 Power Vent Module.
VOLT
HP
Amp
BFPVDRN 10/12
BFPVRNB 10/12
BFPVRH 10/12
CFM
10”12”
BFPVRN 10/12
1.4A
BFPVDWNB 10/12
BFPVWNB 10/12
Power Vent model
1.4A
1.5A
1.5A
1,600
1,600
1,600
1,600
1.5A
5.6A
1,600
6,000
RPM
1,150
Damper
110
1,150
1,150
1,150
1,150
1,750
1/3
5.6A
5.6A
6,000
6,000
1,750
1,750
110
110
110
1/3
1/3
1/3
1/3
1/3
1.4A
1.4A
1,600
1,600
1,150
1,150
BFPVDWN 10/12
BFPVWN 10/12
Montigo BF-Series Exterior Power Vent Systems
NA
NA
BFPVDRNB 10/12
1/3
Mount
Roof
Roof
Wall
Wall
220
220
Roof
Roof
1.5A
1,600
1,150
NA
Wall
Wall
220
220
1/3
Roof 220 1-1/2
NA
NA
BFPVDRH 10/12
Roof 220 1-1/2
Wall 220 1-1/2
BFPVWH 10/12
BFPVDWH 10/12
NA
5.6A
6,000
1,750
Wall 220 1-1/2
BFPVRH5 10/12
12.0A
10,000
2,200
12.0A
10,000
2,200
Roof 220 5
NA
BFPVDRH5 10/12
Roof 220 5
Wall 220
BFPVWH5 10/12
BFPVDWH5 10/12
Wall 220
12.0A
10,000
2,200
12.0A
10,000
2,200
5
NA
5
VOLT
HP
Amp
EXPVDRN 10/12
EXPVWN 10/12
CFM
10”12”
EXPVRN 10/12
1.4A
EXPVDWH 10/12
EXPVWH 10/12
Power Vent model
1.4A
1.4A
3.9A
1,400
1,400
1,400
2,000
3.9A
2,000
Model
RS14
Damper
110
1/3
110
110
110
1/3
1/3
1/3
1/3
1/3
3.9A
3.9A
2,000
2,000
EXPVDRH 10/12
EXPVRH 10/12
Exhausto Exterior Power Vent Systems
NA
NA
EXPVDWN 10/12
1/3
Mount
Roof
Roof
Roof
Roof
110
110
Wall
Wall
1.4A
1,400
NA
Wall
Wall
110
110
1/3
NA
RS14
RS16
RS16
RS14
RS14
RS16
RS16
-
Power Vent
Termination
Power Vent
Termination
16”x 16”x 4”
Deep Elect.
Control Box
One Control Cable Installation
required for either Horizontal
or Vertical Termination.
From ControlBox
20’ Foot, 10-Conductor Cable
to Fireplace, (Standard)
110 VAC 15A
Supply Current
From Dist. Panel
To Control Box
To Next Page
Loading...
Need help?
General