Fisher & Paykel DD24S User Manual

DishDrawer®
Installation instructions
US CA
Important!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our
website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
SAFETY AND WARNINGS
1
Important safety instructions!
Installation of this DishDrawer® requires basic mechanical and electrical skills.
Be sure to leave these Instructions with the Customer.
Installation must comply with your local building and electricity regulations.
At the completion of the DishDrawer® installation, the Installer must perform
Final Check List.
Remove all packaging materials supplied with the DishDrawer®.
This DishDrawer® is manufactured for indoor use only.
Ensure all water connections are turned OFF. It is the responsibility of the plumber and
electrician to ensure that each installation complies with all Codes and Regulations.
The DishDrawer® MUST be installed to allow for future removal from the enclosure if service is required.
The switched power outlet must be outside the DishDrawer® cavity so that it is accessible after
installation.
Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to
the power supply cord.
If the DishDrawer® is to be relocated from one installation to another it must be kept upright to avoid
damage from water spillage.
Make sure only new hoses are used for connection (supplied with DishDrawer®). Old hoses should not
be reused.
Failure to install the DishDrawer® correctly could invalidate any warranty or liability claims.
If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle,
boat or mobile facility containing the product to the service shop at your expense or pay the service
technician’s travel to the location of the product.
DD24S models
WARNING!
Electrical hazard
Before installing the DishDrawer®, remove the house fuse or open the circuit
breaker.
If permanently connecting the DishDrawer®, be sure the power is isolated and
the DishDrawer® unplugged.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of a malfunction or breakdown,
grounding will reduce the risk of electric shock by providing a path of least
resistance for electric current. This appliance is equipped with a cord having
an equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is installed and grounded in accordance
with all local codes and ordinances. WARNING - Improper connection of the
equipment-grounding conductor can result in a risk of electric shock. Check with
a qualified electrician or service representative if you are in doubt as to whether
the appliance is properly grounded.
If the DishDrawer is installed as a permanently connected appliance:
GROUNDING INSTRUCTIONS - This appliance must be connected to a grounded
metal, permanent wiring system, or an equipment-groounding conductor must
be run with the circuit conductors and connected to the equipment-grounding
terminal or lead on the appliance.
Do not modify the power supply plug provided with the appliance - if it will not
fit the outlet, have a proper outlet installed by a qualified electrician. Do not use
an extension cord, adapter plug or multiple outlet box.
Failure to follow this advice may result in electrical shock or death.
WARNING!
Cut hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
(1,1) -1- 599625C DD24S installA2 USCA.indd 14/4/09 2:16:35 PM
(1,1) -1- 599625C DD24S installA2 USCA.indd 14/4/09 2:16:35 PM

Fisher & Paykel DD24S Specifications

General

Brand	Fisher & Paykel
Model	DD24S
Category	Dishwasher
Language	English

Summary

SAFETY AND WARNINGS

Electrical Hazard Warning

Before installing, remove house fuse or open circuit breaker to prevent electrical shock.

Cut Hazard Alert

Warning about sharp panel edges that can cause injury or cuts during installation.

Important Safety Instructions

General safety guidelines for installation including electrical, plumbing, and usage precautions.

PRODUCT DIMENSIONS

Dish Drawer Product Dimensions

Detailed physical dimensions for DD24ST models, including height, width, and depth.

CABINETRY DIMENSIONS

Integrated Model Cavity Height Options

Explains cavity height choices for integrated models to match cabinetry or other appliances.

Cabinetry Installation Dimensions

Provides required cabinet opening dimensions for various DD24ST models and finishes.

Minimum Installation Clearances

Specifies essential clearance measurements required around the unit for proper installation.

PARTS SUPPLIED

List of Supplied Parts

Details all components included with the dishwasher, such as hoses, brackets, and clamps.

CAVITY PREPARATION

Key Cavity Preparation Steps

Important notes on preparing the installation cavity, including services hole protection.

Water Supply Connection Details

Recommended hot water temperature and fitting type for connecting the water supply.

Water Pressure Requirements

Specifies minimum and maximum water pressure limits for water softener and other models.

Hose and Cord Distance Limits

Defines maximum permissible distances for drain hose, inlet hose, and power cord from the chassis edge.

OPTIONALLY HARD WIRING THE PRODUCT

Hard Wiring Installation Steps

Step-by-step guide (A-D) for hard wiring the Dish Drawer, including cable clamp and wiring termination.

ROUTE THE HOSES

Recommended Hose Routing Method

Procedure for routing hoses without removing the drawer, ensuring no kinks or twists.

Alternative Hose Routing Method

Procedure for routing hoses after removing the drawer, ensuring no kinks or twists.

ATTACH SIDE MOUNTING BRACKETS

Side Mounting Bracket Installation

Instructions for attaching side mounting brackets and ensuring correct slot alignment.

REMOVE DRAWER

MOVE INTO THE CAVITY

Top Mounting Bracket Consideration

Note on using top mounting brackets and ensuring secure fitting before sliding unit into cavity.

SECURE THE DRAWER

Sound Insulation Repositioning

Instruction to correctly reposition sound insulation before securing the drawer.

REFIT THE DRAWER

Drawer Clip Reset and Latch Check

Ensures drawer clips are reset and rear latches face forward before refitting.

Hose and Cord Management During Refitting

Check that hoses are not twisted and cord is managed correctly before refitting drawer.

PLUMBING AND DRAINAGE OPTIONS

DishDrawer® with Waste Disposal Setup

Diagram and instructions for connecting the drain to a waste disposal unit.

Dish Drawer® with Air Break Setup

Diagram and instructions for using an air break with a drain hose joiner.

Dish Drawer® with Standpipe Setup

Diagram and instructions for connecting the drain hose to a standpipe.

Proper Hose Routing for Drainage

Ensures drain hoses are routed straight to the joiner, with excess material managed.

FINAL CHECKLIST

Installation and Connection Verification

Checks parts, product security, water supply, and drain connections.

Operation and Drainage Test

Tests power, initial operation, spray arm, and rinse/drainage cycle.

Leakage and Hose Management Checks

Confirms water connections are leak-free and drain hoses are properly supported.

TROUBLESHOOTING

Water Flow and Supply Issues

Addresses excessive water, no water supply, and leaks around connections.

Power and Operation Problems

Troubleshoots issues like no lights when drawer opens.

Physical and Alignment Problems

Covers product tipping, front panel misalignment, and drawer closure issues.