Fisher CL600 - Parts List

ES Valve
Instruction Manual
December 2008
17
Parts List
Note
Part numbers are shown for recommended spares
only. For part numbers not shown, contact your
Emerson Process Management sales office.
Bonnet (figures 3-12)
Key Description Part Number
1 Bonnet/ENVIRO-SEAL bellows seal bonnet
If you need a bonnet or an ENVIRO-SEAL bellows seal
bonnet as a replacement part, order by valve size and
stem diameter, serial number, and desired material.
2 Extension Bonnet Baffle
3 Packing Flange
3 ENVIRO-SEAL bellows seal packing flange
4 Packing Flange Stud
4 ENVIRO-SEAL bellows seal stud bolt
5 Packing Flange Nut
5 ENVIRO-SEAL bellows seal hex nut
6* Packing set, PTFE see following table
6* ENVIRO-SEAL bellows seal packing set
PTFE for 9.5 mm (3/8 inch) stem (1 req’d
for single packing, 2 req’d for double
packing) 12A9016X012
6* ENVIRO-SEAL bellows seal packing set (cont’d)
PTFE for NPS 2 with 12.7 mm (1/2 inch)
stem (2 req’d for double packing) 12A9016X012
PTFE for NPS 3 and 4 with 12.7 mm
(1/2 inch) stem (2 req’d for double
packing) 12A8832X012
7* Packing ring, PTFE composition see following table
7* ENVIRO-SEAL bellows seal packing ring
for low chloride graphite ribbon/filament
packing arrangement
Ribbon packing ring for 9.5 mm (3/8 inch)
and NPS 2 with 12.7 mm (1/2 inch) stem
(4 req’d) 18A0908X012
Filament packing ring for 9.5 mm
(3/8 inch) and NPS 2 with 12.7 mm
(1/2 inch) stem (4 req’d) 1P3905X0172
Ribbon packing ring for NPS 3 and 4
with 12.7 mm (1/2 inch) stem (4 req’d) 18A0918X012
Filament packing ring for NPS 3 and 4
with 12.7 mm (1/2 inch) stem (4 req’d) 14A0915X042
8 Spring
8 Lantern ring
8 ENVIRO-SEAL bellows seal spring
8 ENVIRO-SEAL bellows seal spacer
10 Special washer
Key Description Part Number
11* Packing Box Ring
9.5 mm (3/8 inch) stem,
316 stainless steel 1J873135072
12.7 mm (1/2 inch) stem,
316 stainless steel 1J873235072
19.1 mm (3/4 inch) stem,
316 stainless steel 1J873335072
25.4 mm (1 inch) stem, 17-4PH
stainless steel 1J873435072
31.8 mm (1-1/4 inch) stem, 17-4PH
stainless steel 1J873535072
12* Upper Wiper, felt
9.5 mm (3/8 inch) stem 1J872606332
12.7 mm (1/2 inch) stem 1J872706332
19.1 mm (3/4 inch) stem 1J872806332
25.4 mm (1 inch) stem 1J872906332
31.8 mm (1-1/4 inch) stem 1J873006332
12* ENVIRO-SEAL bellows seal upper wiper
For 9.5 mm (3/8 inch) and NPS 2 with 12.7 mm
(1/2 inch) stem 18A0868X012
For NPS 3 and 4 with 12.7 mm (1/2 inch)
stem 18A0870X012
13* Packing Follower, 316 stainless steel
9.5 mm (3/8 inch) stem 1E943935072
12.7 mm (1/2 inch) stem 1E944335072
19.1 mm (3/4 inch) stem 1E944735072
25.4 mm (1 inch) stem 1H982335072
31.8 mm (1-1/4 inch) stem 1H998435072
13* ENVIRO-SEAL bellows seal bushing
For 9.5 mm (3/8 inch) stem (1 req’d),
for NPS 2 with 12.7 mm (1/2 inch) stem
(2 req’d)
S31600/PTFE 18A0820X012
R30006 18A0819X012
S31600/Cr Ct 11B1155X012
For NPS 3 and 4 with 12.7 mm (1/2 inch)
stem (1 req’d)
S31600/PTFE 18A0824X012
R30006 18A0823X012
S31600/Cr Ct 11B1157X012
13* ENVIRO-SEAL bellows seal bushing/liner
For 9.5 mm (3/8 inch) stem (1 req’d),
for NPS 2 with 12.7 mm (1/2 inch) stem
(2 req’d)
N10276 bushing, PTFE/glass liner 12B2713X012
N10276 bushing, PTFE/carbon liner 12B2713X042
For NPS 3 and 4 with 12.7 mm (1/2 inch)
stem (1 req’d)
N10276 bushing, PTFE/glass liner 12B2715X012
N10276 bushing, PTFE/carbon liner 12B2715X042
14 Pipe Plug for 1/4 NPT Tapping in Packing Box
14 Lubricator
14 Lubricator/Isolating Valve
15 Yoke Locknut
15 ENVIRO-SEAL bellows seal Locknut
16 Pipe Plug for 1/2 NPT Tapped Extension Bonnets
16 ENVIRO-SEAL bellows seal pipe plug
*Recommended spare parts