Flex SBG 4910 - Operating Instructions; Cutting Rate; Maintenance and Care

SBG 4910
23
Operating instructions
Cutting rate
Cutting into solid
material: Setting I (60 m/min)
Cutting into hollow
material: Setting II (80 m/min)
Cutting area
Clamping the material correctly
in the vice
klqb>
fÑ=éêçÑáäÉë=~êÉ=ã~ÇÉ=çÑ=~=îÉêó=íÜáå=ã~íÉêá~äI=
áåëÉêí=~åçíÜÉê=éáÉÅÉ=áåíç=íÜÉ=éêçÑáäÉ=ïÜáÅÜ=
ã~íÅÜÉë=íÜÉ=ëÜ~éÉ=çÑ=íÜÉ=éêçÑáäÉI=íÜÉêÉÄó=
êÉÇìÅáåÖ=íÜÉ=êáëâ=çÑ=ÇáëíçêíáçåK
Maintenance and care
t^okfkd>
_ÉÑçêÉ=éÉêÑçêãáåÖ=~åó=ïçêâ=çå=íÜÉ=éçïÉê=
íççäI=éìää=çìí=íÜÉ=ã~áåë=éäìÖK
Cleaning
`^rqflk>
ofph=lc=fkgrov>
kÉîÉê=ìëÉ=ÅçãéêÉëëÉÇ=~áê=íç=Ääçï=ëï~êÑ=
~ï~óK
 Regularly clean the power tool.
 Regularly remove cut-offs and swarf from
the cutting area.
Prolonged non-use
 Clean the power tool.
 Relieve the tension on the saw band.
 Store the machine in a dry, well ventilated
room.
Repairs
klqb>
rëÉ=çåäó=çêáÖáå~ä=é~êíë=ëìééäáÉÇ=Äó=íÜÉ=ã~åìJ
Ñ~ÅíìêÉê=Ñçê=êÉéä~ÅÉãÉåí=éìêéçëÉëK=
fÑ åçåJçêáÖáå~ä=é~êíë=~êÉ=ìëÉÇI=íÜÉ=Öì~ê~åíÉÉ=
çÄäáÖ~íáçåë=çÑ=íÜÉ=ã~åìÑ~ÅíìêÉê=ïáää=
ÄÉ ÇÉÉãÉÇ=åìää=~åÇ=îçáÇK
oÉé~áêë=ëìÅÜ=~ë=êÉéä~ÅáåÖ=~=Ç~ã~ÖÉÇ=ÅçêÇI=
ã~ó=ÄÉ=Å~êêáÉÇ=çìí=Äó=~å=~ìíÜçêáëÉÇ=
ÅìëíçãÉê=ëÉêîáÅÉ=ÅÉåíêÉ=çåäóK
Spare parts and accessories
Other accessories, in particular insertion
tools, can be found in the manufacturer’s
catalogues.
Exploded drawings and spare-part lists
can be found on our homepage:
www.flex-tools.com
Workpiece
profile
Cutting
angle
Cutting area
[mm]
< 80
0 ° < 80
< 80 x 100
< 68
45 ° < 60
< 55 x 68
< 80
Free-hand
sawing
< 80
< 80 x 150