Fluke 80i-600 User Manual

FL.UKE~
Instruction Sheet
80i-600
AC Current Probe
INTRODUCTION
The Model 80i-600 is a clamp-on ac current probe designed
to extend the current
me<lsuring c<lp<lbility of an ac current
meter to 600 amperes. A clamp-on, 1000-turn coil designed
into the probe allows measurements to be made
without
breabng the circuit under test. The coil serves as the second-
ary of a current transformer. Thecurrent carrying conductor
being measured serves as the primary. Because
of a high
efficiency, quadrature type
of winding used. wire size ,md
the position of the wire within the prohe jaws does not effect
accuracy.
SPECIFICATIONS
Input Current Range: I A to 600A
Output: I milli<lmp per ampere of input current (1 mAl A)
Accuracy: Accuracy: ±Y; of rcadiJ)~. :,U HI tn I KHI.
±39'0 of reading (typical). 30 Hz to 5U HI or I KHI to 10 KHz.
Working Voltage: 750Y ac nns maximum
Maximum Conductor Size: 50.8 nml (2 inch.)
Shunt (load) Resistance: less than 12 ohms at multim-
eter input to maintain specified accuracy
Typical Bandwidth: -10% at 10 Hz and 50 kHz (lA, 400
Hz reference, excludes multimeter response)
Usable Current Range: O.I{\. to 2000A, 5 seconds Ill<lxi-
mum above 600A
Safety: Protection Class Class II as defined in IEC 348 and
ANSI
09.5
MULTIMETER COMPATIBILITY
The 80i-600 is compatible with any multimeter capable of
reading ac current equal to 111000 of the current to be
measured. To take full advantage of the probe's accuracy, a
multimeter ac current accuracy
of ±O.75% or better is
recommended. A voltmeterfitted with an external shunt will
qualify as a suitable current meter. However, to ensure
the
probe'saccuracy, the shunt(or multimeterinput resistance in
ac current) should be less than 12 ohms. This requirement is
met on Fluke
DMM' s when using a current range of 20 mA
or greater.
Advanced Test Equipment Rentals
www.atecorp.com 800-404-ATEC (2832)
®
E
s
t
a
b
l
i
s
h
e
d
1
9
8
1

Fluke 80i-600 Specifications

General

Current Range	1 A to 600 A AC
Output Voltage	1 mV/A
Maximum Voltage	600 V AC rms
Power Supply	9 V battery
Operating Temperature	0°C to 50°C (32°F to 122°F)
Storage Temperature	-20°C to 60°C (-4°F to 140°F)
Safety Rating	CAT III 600 V
Category	Current Probe
Output Connector	BNC
Weight	230 g

Summary

Instruction Sheet 80i-600 AC Current Probe

Introduction

Describes the Model 80i-600 as a clamp-on AC current probe extending current measuring capability to 600A.

AC Current Probe Specifications

Input Current Range

Specifies the operational input current range for the probe, from 1A to 600A.

Output Signal

Defines the probe's output as 1 milliamp per ampere of input current (1mA/A).

Accuracy and Bandwidth

Details measurement accuracy at different frequencies and the typical bandwidth.

Voltage, Conductor Size, and Resistance

Specifies maximum working voltage, maximum conductor size, and required shunt resistance.

Usable Current Range and Safety

Defines extended usable current range and identifies the safety protection class.

Multimeter Compatibility

Compatibility Requirements

Explains requirements for compatible multimeters and recommended accuracy for optimal probe performance.

Measurement and Operation Guidelines

Meter Readings

Explains how meter readings correlate to the actual input current when using the probe.

Low-Level Current Measurements

Details methods for measuring currents below 1A using loop techniques.

Operational Steps

Provides step-by-step instructions for connecting, setting up, and using the probe with a meter.

Maintenance and Setup

Performance Test Procedure

Outlines a procedure to verify the probe's accuracy using a calibrated current source.

Cleaning Instructions

Provides guidance on how to clean the probe safely and effectively.

Clamp/Meter Setup Guide

A table detailing meter setup for various Fluke models for use with the probe.