Fortin EVO-START User Manual

INSTALL GUIDE
GUIDE D’INSTALLATION
INSTALL GUIDE
REV.: 20161206
WWW.EVO-START.CA
WWW.FORTIN.CA
WARNING MISE EN GARDE
Neither the manufacturer or distributor of this
module is responsible for damages of any kind
either indirectly or directly caused by this module,
except for the replacement of this module in case
of manufacturing defects. This module must be
installed by a quali ed technician.
This instruction guide may change without notice.
Visit WWW.FORTIN.CA or WWW.EVO-START.CA to
obtain the latest version.
Ni le manufacturier, ni le distributeur ne se
considèrent responsables des dommages causés ou
ayant pu être causés, indirectement ou directement,
par ce module, excepté le remplacement de ce
module en cas de défaut de fabrication. Ce module
doit être installé par un technicien quali é. Ce guide
d’instruction peut faire l’objet de changement sans
préavis. Consultez le WWW.FORTIN.CA ou
WWW.EVO-START.CA pour voir la plus récente
version.
1X
EVO-ONE or
E400 or
EVO-ALL
EVO-ONE ou
E400 ou
EVO-ALL
1X
FLASH LINK UPDATER 2 FLASH LINK UPDATER 2
1X
Microsoft Windows Computer & Internet
connection
Ordinateur Microsoft Windows & connection
Internet
PARTS REQUIRED (NOT INCLUDED) PIÈCES REQUISES (NON INCLUSES)
TABLE OF CONTENT TABLE DES MATIÈRES
Page 1 / 16
INSTALL WITH :
INSTALLATION AVEC :
EVO-ONE* ............................................................. PAGES 2 - 5
E400* ...................................................................... PAGES 6 - 9
EVO-ALL STANDALONE* .................................. PAGES 10 - 13
DIAGNOSTICS ......................................................................... PAGES 14
DIAGNOSTIQUES
FACTORY RESET .................................................................... PAGES 15
RÉINITIALISATION D’USINE
*Sold separately
*Vendu séparément
GUIDE # 59871

Fortin EVO-START Specifications

General

Brand	Fortin
Model	EVO-START
Category	Remote Starter
Language	English

Summary

Fortin EVO-START Install Guide

Factory Reset Procedure

Procedure to reset the module to factory default settings.

Important Warnings and Disclaimer

Manufacturer's disclaimer of liability and installation by qualified technician.

EVO-START and EVO-ONE Wiring

High Current Wiring Connections

Details on high current or T-harness connections for EVO-ONE.

Low Current Wiring Connections

Details on low current (2AMP) connections for EVO-ONE.

EVO-START Programming Steps

EVO-START Programming with Valet Button

Procedure to program EVO-START using the valet button.

EVO-START Programming without Valet Button

Procedure to program EVO-START without the valet button.

EVO-START Programming Completion

Module Programming Confirmation

Confirmation that the module has been successfully programmed.

EVO-START and E400 Wiring

E400 High Current Wiring

Details on high current or T-harness connections for the E400.

E400 Low Current Wiring

Details on low current (2AMP) connections for the E400.

E400 EVO-START Programming

E400 EVO-START Programming with Valet Button

Procedure to program E400 EVO-START using valet button.

E400 EVO-START Programming without Valet Button

Procedure to program E400 EVO-START without valet button.

E400 EVO-START Programming Completion

E400 Module Programming Confirmation

Confirmation of successful E400 module programming.

EVO-START and EVO-ALL Wiring

EVO-ALL T-Harness Wiring

Details on T-harness connections for the EVO-ALL module.

EVO-ALL Without T-Harness Wiring

Details on wiring for the EVO-ALL module without a T-harness.

EVO-ALL EVO-START Programming

Diagnostic Codes and Events

LED Status Indicators

Diagnostic Event Descriptions

Diagnostic Action Recommendations

Factory Reset Procedure

Disconnect Harness for Reset

Reconnect Harness and Press Button

Hold Button Until Amber LED

Reprogramming After Factory Reset