How to resolve communication trouble between outdoor unit and driver in Friedrich FPHSW09A1B?
If your Friedrich Air Conditioner is experiencing communication trouble between the outdoor unit and the driver, start by checking the connection wires to ensure they are not loose. If the wires are secure, the outdoor board or drive board may have failed and require replacement.
What to do about communication trouble between my Friedrich Air Conditioner's outdoor unit and driver?
Communication trouble between the outdoor unit and driver of your Friedrich Air Conditioner can be due to: * Loose connection wires; secure any loose connection wires. * A failed outdoor board or drive board; replace the outdoor board or drive board.
How to fix communication failure between indoor and outdoor unit of Friedrich FPHSW09A1B?
A communication failure between the indoor and outdoor units of your Friedrich Air Conditioner can occur for several reasons: * The communication cable connector may be loose; ensure it is securely connected. * The connection between the filter board and the terminal might be incorrect or loose; verify the connection is correct and secure. * The communication cable itself might be faulty and need replacement. * The connection between the filter board and the outdoor control board might be incorrect or loose; verify the connection is correct and secure. * A failure in the indoor control board, PFC board, power board, or outdoor control board could also be the cause, requiring replacement of the respective board.
What to do if my Friedrich FPHSW09A1B Air Conditioner has current overload protection?
If your Friedrich Air Conditioner is experiencing current overload protection, it could be due to: * The fan motor running abnormally, in which case you should check and repair the fan motor. * Dirty condenser and evaporator coils, so you should clean them. * Abnormal air inlet and outlet; ensure that they are unobstructed.
What causes anti-freeze or overload protection in my Friedrich Air Conditioner indoor unit?
If your Friedrich Air Conditioner is experiencing 'Anti-freeze protection with cooling or overload protection with heating in indoor unit', start by checking the indoor coil temperature sensor connector to ensure it's properly connected. If the connector is fine, the indoor coil temperature sensor itself may have failed and need replacement. If the problem persists, the indoor control board might be faulty and require replacement. Additionally, consider checking the refrigerant system for any abnormalities.
What to do if my Friedrich FPHSW09A1B shows outdoor EEPROM faulted?
If your Friedrich Air Conditioner displays an 'Outdoor EEPROM faulted' error, first check if the EEPROM chip is loose. If it is, ensure it's properly secured. Also, verify that the EEPROM chip is inserted in the correct direction. If the chip is correctly oriented and secured, the EEPROM chip itself may have failed and need to be replaced.
What to do if Friedrich Air Conditioner shows maximum current protection?
If your Friedrich Air Conditioner is showing maximum current protection, it could be due to a short circuit. This could be in the outdoor control board, the drive board, or other components. It is suggested to replace the outdoor control board or drive board if they are short-circuited. Inspect and replace any other short-circuited components.
What to do if there is a communication failure between the indoor unit and outdoor unit in my Friedrich Air Conditioner?
If your Friedrich Air Conditioner is experiencing communication failure between the indoor and outdoor units, there are several potential causes. First, check the communication cable connector to ensure it is secure. If the connector is fine, the communication cable itself may have failed and need replacement. Also, verify the connection between the filter board and both the outdoor control board and the terminal, ensuring they are correctly connected and not loose. Other potential causes include a failed indoor control board, PFC board, power board, or outdoor control board, any of which would require replacement.
What to do if the outdoor coil temperature sensor faulted on my Friedrich FPHSW09A1B?
If the outdoor coil temperature sensor faulted on your Friedrich Air Conditioner, it could be due to: * A loose outdoor coil sensor connector, which should be secured. * A failed outdoor coil temperature sensor, which should be replaced. * A failed outdoor control board, which should be replaced.
What causes a compressor drive fault in my Friedrich FPHSW09A1B?
A compressor drive fault in your Friedrich Air Conditioner can be caused by: * A failed outdoor drive board, which would need to be replaced. * A failed compressor, which would also need replacement. * A failed outdoor control board, requiring replacement.
Essential safety guidelines for handling and operating the equipment.
Detailed technical specifications for 9k and 12k BTU models.
Explanation of the remote control functions, buttons, and indicators.
Visual guide showing required clearances and mounting dimensions.
Procedure for leak testing, evacuating, and charging the refrigerant system.
Illustrations and descriptions of the 2-way and 3-way service valves.
Provides resistance values for indoor coil and room sensor at various temperatures.
Lists error codes for outdoor and indoor units and their potential causes.
General| Cooling Capacity | 9, 000 BTU |
|---|---|
| Energy Efficiency Ratio (EER) | 12.0 |
| Dehumidification | 2.5 pints/hour |
| Air Flow | 250 CFM |
| Area to Cool | Up to 400 sq. ft. |
| Voltage | 115V |
| Window Height (min) | 14" |
| EER | 12.0 |
| Operating Voltage | 115V |
| Operating Frequency | 60Hz |
| Air Flow (High) | 250 CFM |
| Noise Level (High) | 52 dB |
| Refrigerant | R-32 |
| Power Supply | 115V |
| Plug Type | 5-15P |
| Window Width (min/max) | 23-36 inches |
To Next Page
