Frigidaire FRA12EHT2 User Manual

READ BEFORE INSTALLING UNIT
For Through-the-Wall Air Conditioners
1
Installation Instructions
NOTE:
DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED HERE
Note that the air conditioner dimensions are: 24" wide,14" high, and 19" deep (without front). Install Air Conditioner
according to these installation instructions to achieve the best performance. Save these installation instructions for
future reference.
Do This First (for existing sleeve)
You may not need all parts in the kit. Discard unused parts.
Items in Kit
2020213A0734
Hardware
2
2
3
Tapered Spacer Blocks (17” Long)
Plastic Divider ( )
4
Stuffer Seal ( )
4
1
2
3
4
5 seal ( )
1
6
2
73
8
No. Qty.
2
9
Centering/Support Blocks ( ” )
4 ” x 3 ” x 1
1
2
1
2
1
2
” x 4 ” x 14 ”
1
8
1
2
1
2
1” x 1 ” x 84”
1
2
1” x 1 ” x 25”
1
2
seal ( )
1” x 1 ” x 14”
1
2
seal ( )
1” x 3/8” x 25”
seal ( )
1” x 3/8” x 14”
seal ( )
1” x 3/4” x 14”
2
Hardware
2
1
1
Ground Wire (green)
2
13
10
11
12
14 Grounding Screw
15 1
16 1
17
No. Qty.
4
18
Trim Frame (top & bottom legs)
Grille (plastic)
Grille Aluminum
Nuts (plastic)
Screw w/washer
4
Trim Frame (side legs)
Toothed washer for grounding screw
2
Pay attention to danger and safety notices.
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may
be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install
the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. To
prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended
period of time.
Handle air conditioner with care.
Make sure air conditioner does not fall during installation.
Carefully read the installation manual before beginning.
Follow each step as shown.
Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.
INSTALLATION WARNINGS AND CAUTION

Frigidaire FRA12EHT2 Specifications

General

Cooling Capacity	12, 000 BTU
Room Size Coverage	550 sq. ft.
Power Supply	115V/60Hz
Type	Window Air Conditioner
Operating Frequency	60 Hz
Cooling Amps	10.8 A

Summary

INSTALLATION WARNINGS AND CAUTION

PREPARATORY STEPS

Do This First (for existing sleeve)

Initial preparation steps before installing the unit, including checking dimensions.

Items in Kit

Lists all hardware and parts included in the installation kit for the air conditioner.

HOW TO INSTALL GENERAL STEPS

Identify Wall Sleeve Brand and Dimensions

Match your wall sleeve to the correct dimensions from the provided chart for proper installation.

Prepare Wall Sleeve

Steps to clean, secure the wall sleeve, and drill a hole for the grounding screw.

BRAND-SPECIFIC WALL SLEEVE INSTALLATION

Emerson (15" Deep)

Instructions for installing the unit in an Emerson 15" deep wall sleeve.

Fedders (19-3/4" Deep)

Instructions for installing the unit in a Fedders 19-3/4" deep wall sleeve.

Fedders or Friedrich (16-3/4" Deep)

Instructions for installing the unit in a Fedders or Friedrich 16-3/4" deep wall sleeve.

General Electric/Hotpoint (16-7/8" Deep)

Instructions for installing the unit in a GE/Hotpoint 16-7/8" deep wall sleeve.

Sears or Carrier 51S Series (18-5/8" Deep)

Instructions for installing the unit in a Sears or Carrier 51S Series 18-5/8" deep sleeve.

Whirlpool (17-1/8" Deep)

Instructions for installing the unit in a Whirlpool 17-1/8" deep wall sleeve.

Whirlpool (23" Deep)

Specific instructions for installing the unit in a Whirlpool 23" deep wall sleeve.

White Westinghouse/Frigidaire/Carrier 52F Series (16" + 17-1/2" Deep)

Instructions for White Westinghouse, Frigidaire, or Carrier 52F Series sleeves.

White Westinghouse or Frigidaire (22" Deep)

Instructions for installing the unit in White Westinghouse or Frigidaire 22" deep sleeves.

ALTERNATIVE MOUNTING METHODS

Direct Unit Mounting

Method for directly mounting the rear grille to the unit as a last resort.

FINISHING INSTALLATION