Frontier TR2058 - User Manual

Questions and Answers

M
Marc EsparzaAug 18, 2025
What to do if my Frontier Tiller machine smells hot or begins to smoke?
- Q
  qperezAug 18, 2025
  If your Frontier Tiller machine smells hot or begins to smoke, it could be due to several reasons. Trash might be heavily wrapped around the bearing protection covers, causing friction. Remove any trash immediately to prevent bearing damage. Also, check the oil level in the gearbox and the lubricant on the chain. If your machine has a slip clutch, inspect it and adjust if necessary.
L
Lauren SmithAug 20, 2025
Why does my Frontier TR2058 machine skip and leave crop residue?
- S
  Stephanie JohnsonAug 20, 2025
  If your Frontier Tiller machine skips and leaves crop residue, start by checking for badly worn blades. If the blades are worn down to the tip, the overlap will be lost, and cutting will deteriorate; replace them as needed. If your machine uses a slip clutch, check its performance. Additionally, reduce your ground speed.
C
cynthiaryanAug 23, 2025
What to do if PTO is turning but not blades on Frontier Tiller?
- J
  Jesus JohnsonAug 23, 2025
  If the PTO is turning but the blades are not on your Frontier Tiller, the slip clutch may be slipping. You should adjust the slip clutch or replace the discs.
B
Brooke MirandaAug 26, 2025
Why is the gearbox noise noticeable and constant on my Frontier Tiller?
- V
  Vincent OwensAug 26, 2025
  If the gearbox noise on your Frontier Tiller is noticeable and constant, especially on a new machine, this can be normal until it has been run in. However, check the oil level. If the noise persists, worn gears may be the cause, and you should replace them.
M
Michael JonesAug 28, 2025
What to do if blades stop turning but PTO, gearbox and hexshaft are on Frontier TR2058 Tiller?
- J
  John VillaAug 28, 2025
  If the blades on your Frontier Tiller stop turning while the PTO, gearbox, and hexshaft are still turning, a broken drive chain is likely the cause. Remove the chain case and check for a broken connector link.
A
Amy LambertAug 30, 2025
Why does the PTO vibrate on my Frontier Tiller?
- C
  Christina CarterAug 31, 2025
  If the PTO vibrates on your Frontier Tiller, it could be due to worn cross and bearings. Replace the worn cross and bearings. It could also be that the machine is working too high, causing the driveline to be at too great of an angle. Also, check the rotor shaft for any wrappings.
N
Nicole GrantSep 2, 2025
How to fix an oil leak from the gearbox of Frontier TR2058?
- L
  Lauren WarnerSep 2, 2025
  If you notice an oil leak from the gearbox of your Frontier Tiller, it could be due to a damaged oil seal. Replace the oil seal. Alternatively, the gearbox might be overfilled; remove the excess oil.
K
Kimberly MurphySep 4, 2025
Why does my Frontier TR2058 Tiller make an intermittent clicking noise?
- R
  Robert ColemanSep 4, 2025
  If your Frontier Tiller machine makes an intermittent clicking noise, it could be due to loose blade bolts, so tighten them. It could also be that the gearbox gears or chain are damaged, so replace the damaged gears or chain.
J
Jasmine CastroSep 7, 2025
What to do if the roller is not turning freely on Frontier TR2058 Tiller?
- A
  Adam WalkerSep 7, 2025
  If the roller on your Frontier Tiller is not turning freely, check for trash or mud buildup on the roller end.
R
Raymond MorseSep 9, 2025
Why is there uneven seed distribution with my Frontier Tiller?
- Z
  zweaverSep 9, 2025
  If you experience uneven seed distribution with your Frontier Tiller, the seed cups might be obstructed. Check for plugging in the seed cup. Also, reduce your ground speed and check for trash or mud buildup on the roller.