DIGITAL TELEMETRY RADIO SYSTEM
MENU
PAGE
EXIT
ENT
2.4GHz
7.1v
MODEL01
SA
SB
SC
SD
-
-
-
SE
SF
SG
SH
03:04
OPEN
TX
SCS2 SDSA S1SB
FrSky Electronic Co., Ltd
Website:www.frsky-rc.com E-mail:frsky@frsky-rc.com Technical Support: sales4tech@gmail.com
Introduction
Thank you for purchasing the FrSky 2.4GHz ACCST TARANIS X9D Plus digital telemetry radio system. In order to
make the best use of your system and to fly safely, please read this manual carefully. If you have any difficulties
while using your system,please consult the manual , your hobby dealer, or FrSky technical support.
Meanings of Special Markings
Pay special attention to safety where indicated by the following marks:
DANGER- Procedures which may lead to dangerous conditions and cause death/serious injury if not carried out
properly.
WARNING- Procedur
es which may lead to a dangerous condition or cause death or serious injury to the user if
not carried out properly or procedures where the probability of superficial injury or physical damage is high.
CAUTION- Procedures where the possibility of serious injury to the user is small, but there is a danger of injury,
or physical damage, if not carried out properly.
= Mandatory = Prohibited
Warning: Always keep electrical components away from small children.
www.frsky-rc.com
FrSky 2.4GHz ACCST Taranis X9D Plus Manual
SC
SG
MENU
PAGE
EXIT ENT
Antenna
Digital Trim
Slider
power switch
Hook
Stick
(J3)
(J4)
Stick
(J1)
(J2)
LCD Display
SE
SA
SH
SF
SB
S1
S2
SD
Slider
(Switch Default Settings)
SA: 3 positions, Short Lever
SB: 3 positions, Long Lever
SC: 3 positions, Long Lever
SD: 3 positions, Short Lever
SE: 3 positions, Short Lever
SF: 2 positions, Long Lever
SG: 3 positions; Short lever
SH: 2 positions, Momentary;
Long Lever
You can choose the Switch and define
its positions in the Mixer menu.
Overview
Trainer Port
USB Port
Charge Jack
Battery Cover
Earphone Port
Carrying Bar
Power Indicator LED
Due to unforeseen changes in production, the information contained in this manual is subject to change without notice.
FrSky Electronic Co., Ltd
Website:www.frsky-rc.com E-mail: frsky@frsky-rc.com Technical Support: sales4tech@gmail.com
www.frsky-rc.com
Strong SignalStrong Signal
Weak Signal
Cautions on handling antenna
Do not touch the antenna during operation. Doing so could interfere with transmission, causing a crash.
Do not carry the transmitter by the antenna.The antenna wire could break and prevent transmission.
Do not pull the antenna forcefully. The antenna wire could break and prevent transmission.
Rotating Antenna
The antenna can be rotated 180 degrees and angled 90
degrees. Forcing the antenna further than this can cause
damage to the antenna. The antenna is not removable.
Angle adjustment of the antenna
The antenna rotation and angle can be adjusted. The antenna
features week radio signal in the forward direction and strong
radio signal in the sideways directions. Adjust the antenna
angle to match your flying style.
Specifications
Model Name: Taranis X9D Plus
Number of Channels: Up to 16 channels
Operating Voltage Range:6~15V (2S, 3S Lipos are acceptable)
Operating Current: 260mA maximum (both RF module and backlit are on)
Operating Temperature: -10~60℃
Backlight LCD Screen: 212*64, 2 color combinations for select
Model Memories: 60 (extendable by SD card)
Compatibility: FrSky X series, D series and V8-II series receivers (plus other receivers if an external module is used)
Taranis X9D Plus-EU version is only compatible with X series receiver EU version.
●
●
●
●
●
●
●
●
Quad Ball Bearing Gimbals
Receiver Match
Audio Speech Outputs (values, alarms, settings, etc.)
Real-time Flight Data Logging
Receiver Signal Strength Indicator (RSSI) Alerts
Super Low Latency
Smart Port Supported
Vibration Alerts
Features
DIGITAL TELEMETRY RADIO SYSTEM
MENU
PAGE
EXIT
ENT
2.4GHz
7.1v
MODEL01
SA
SB
SC
SD
-
-
-
SE
SF
SG
SH
03:04
OPEN
TX
SCS2 SDSA S1SB
FrSky Electronic Co., Ltd
Website:www.frsky-rc.com E-mail: frsky@frsky-rc.com Technical Support: sales4tech@gmail.com
www.frsky-rc.com
●
Notice:
The above instructions do not apply to D-series and
L-series receivers, which require the internal RF
module of Taranis X9D Plus to be in D8 mode or LR12
mode. For these receivers, failsafe must be set on the
receiver side (see receiver instructions).
FrSky Electronic Co., Ltd
Website:www.frsky-rc.com E-mail: frsky@frsky-rc.com Technical Support: sales4tech@gmail.com
www.frsky-rc.com
Notes and Warnings for Battery & Charger
Please connect the provided battery in the battery compartment before use.
The six-cell NiMH battery is for use only in your TARANIS X9D Plus.
Be sure to use the built-in battery charger to charge the battery.
Be careful not to drop the battery.
Don't pull the battery wires as this could produce,short-circuits and cause the battery to explode.
Do not remove the battery from the TARANIS X9D Plus transmitter while the voltage warning is blinking as this
could cause internal settings and memories to be destroyed.
Do not use the transmitter if a “Backup Error” warning occurs.
Be sure to turn off the Taranis X9D Plus before charging the battery.
The Power Indicator LED will be on during charging, and be off after the charging is finished.
Battery
Connecter
Reserved
TF card slot
Battery Connector Polarity
Ensure that the battery connector polarity is correct when
connecting batteries others than the provided 6cell NiMH
battery into the battery compartment, otherwise the Taranis
X9D Plus might not be powered .
Model Setup for Taranis X9D Plus Internal RF Module
The internal RF module of FrSky Taranis X9D Plus is newly developed by FrSky under the name of XJT.
Enter the MODEL SETUP menu (for details, refer to the Guide included on the SD card, or download it from FrSky
website).
Step 1: Set the Mode for Taranis X9D Plus Internal RF
Refer to the table below and set the Taranis X9D Plus to the mode corresponding to your receiver (D8, D16 or LR12).
Model Setup for Taranis X9D Plus External RF Module
Step 3: Set the Receiver Number
When you create a new model, the system will assign you a receiver number automatically, but this can be easily
changed.The range of the receiver number is 00-63, with the default number being 01(use o 00 is not
recommended). Once the receiver is set to the desired number and is bound to the Taranis X9D Plus, the bind
procedure will not need to be repeated unless the receiver number is changed, In this case, either set the receiver
number to the previous one, repeat the bind procedure.
Step 4: Bind
Bind refers to Taranis X9D Plus binding mode. Move the cursor to “Bind”, press ENTER button, the cursor will flash
and the speaker will beep to remind you that the RF module has entered the bind mode. Then put your receiver into
binding mode and finish the bind procedure(refer to the receiver’s manual for details). Press Enter or EXIT to exit.
Step 5: Set Failsafe mode
There are 4 failsafe modes: No Pulse, Hold, Custom, Receiver (this mode only used above opentx-v2.0.0 firmware)
● No Pulse: on loss of signal the receiver produces no pulses on any channel. To use this type, select it in the
menu and wait 9 seconds for the failsafe to take effect.
● Hold: the receiver continues to output the last positions before signal was lost. To use this type, select it in the
menu and wait 9 seconds for the failsafe to take effect.
● Custom: pre-set to required positions on lost signal. Move the cursor to “Set” and press ENTER, you will see
FAILSAFE SETTING screen below. Move the cursor to the channel you want to set failsafe on, and press
ENTER. When moving the crresponding sticks or switches, you will see the channel bar moving. Move the
channel bar to the place you want for failsafe and long press ENTER to finish the setting. Wait 9 seconds before
the failsafe takes effect.
● Receiver: set the failsafe on the receiver(see receiver instructions) in D16 mode, select it in the menu and wait 9
seconds for the failsafe to take effec.
Step 6: Range
Range refers to Taranis X9D Plus range check mode. A pre-flight range check should be done before each flying
session. Move the cursor to “Range” and press ENTER. In range check mode, the effective distance will be
decreased to 1/30. Press Enter or EXIT to exit.
The external RF module can be powered on or off by software. The setup process is the same as that for the
internal RF. If you use other brand RF module than FrSky, please choose PPM mode.
Step 2: Set the Channel Range
The internal RF module of Taranis X9D Plus supports up to 16 channels. The channel range is configurable, and
needs double check before use.
Mode of Taranis X9D Plus
Mode of Taranis
X9D Plus-EU version
Compatible Receivers Number of Output Channels
Compatible Receivers Number of Output Channels
D8
D16-EU X series-EU version Up to 16 channels
D16
LR12
X series (X8R, etc.)
L series (L9R, etc.)
Up to 16 channels
12 channels
8 channels
V8-II series in D mode (V8FR-II,
V8R7-II,V8R4-II,VD5M,etc.)
D series (D8R-II plus, D8R-XP,
D6FR,D4R-II,etc.)
Notice: Older V8 receivers are not supported by the internal module but can be used
with an external DJT module in V8 mode.
Taranis X9D Plus-EU version only has D16-EU mode.
To Next Page
Need help?
General
