FINEPIX XP170
BL01731-100
BG
This document describes cautions on using a wireless transmitter
For more details or other functions, refer to the supplied XP100/XP110 Owner’s Manual or CD-ROM.
Regarding the Declaration of Conformity, visit http://www.fujifi lm.com/products/digital_cameras/index.html.
IMPORTANT: Read the following notices before using the camera’s built-in wireless transmitter.
Q This product, which contains encryption function developed in the United States, is controlled by the United States Export Administration Regulations and
may not be exported or re-exported to any country to which the United States embargoes goods.
• Use only as part of a wireless network. FUJIFILM does not accept liability for damages resulting from unauthorized use. Do not use in applications requiring
a high degree of reliability, for example in medical devices or other systems that may directly or indirectly impact human life. When using the device in
computer and other systems that demand a greater degree of reliability than wireless networks, be sure to take all necessary precautions to ensure safety
and prevent malfunction.
• Use only in the country in which the device was purchased. This device conforms to regulations governing wireless network devices in the country in which it was
purchased. Observe all location regulations when using the device. FUJIFILM does not accept liability for problems arising from use in other jurisdictions.
• Wireless data (images) may be intercepted by third parties. The security of data transmitted over wireless networks is not guaranteed.
• Do not use the device in locations subject to magnetic elds, static electricity, or radio interference. Do not use the transmitter in the vicinity of microwave ovens or
in other locations subject to magnetic fi elds, static electricity, or radio interference that may prevent reception of wireless signals. Mutual interference may
occur when the transmitter is used in the vicinity of other wireless devices operating in the 2.4GHz band.
• The wireless transmitter operates in the 2.4GHz band using DSSS and OFDM modulation.
Wireless Network Devices: Cautions
• This device operates on the same frequency as commercial, educational, and medical devices and wireless transmitters. It also operates on the same frequency as
licensed transmitters and special unlicensed low-voltage transmitters used in RFID tracking systems for assembly lines and in other similar applications.
• To prevent interference with the above devices, observe the following precautions. Confi rm that the RFID transmitter is not in operation before using this device.
Should you observe that the device causes interference in licensed transmitters used for RFID tracking, immediately choose a new operating frequency for
this device to prevent additional interference. If you notice that this device causes interference in low-voltage RFID tracing systems, contact a FUJIFILM
representative.
WARNING
Turn the camera o in crowds. The camera emits radio-frequency radiation that may interfere with pacemakers.
Turn the camera o in the vicinity of automatic doors, public address systems, and other automatically controlled devices. The camera emits radio-
frequency radiation that may cause these devices to malfunction.
Keep the camera at least 22cm away from people wearing pacemakers. The camera emits radio-frequency radiation that may interfere with pacemakers.
For Customers in the U.S. A.For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Contains FCC ID :W2Z-02000001Contains FCC ID : W2Z-02000001
Contains IC :W2Z-02000001Contains IC : 7736B-02100001
FCC Statement: This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
CAUTION: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• You are cautioned that any changes or modifi cations not expressly ap-
proved in this manual could void the user’s authority to operate the
equipment.
Notes on the Grant: To comply with Part 15 of the FCC Rules, this product
must be used with a Fujifi lm-specifi ed ferrite-core A/V cable, USB cable, and
DC supply cord.
European Union regulatory noticeEuropean Union regulatory notice
This product complies with the following EU Directives:
• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmo-
nized European standards (European Norms) which are listed on the EU
Declaration of Conformity issued by FUJIFILM Corporation for this product
or product family.
This compliance is indicated by the following conformity marking placed
on the product:
This marking is valid for non-Telecom products and EU harmonized Telecom
products (e.g. Bluetooth).
CS
This document describes cautions on using a wireless transmitter
For more details or other functions, refer to the supplied XP100/XP110 Owner’s Manual or CD-ROM.
Regarding the Declaration of Conformity, visit http://www.fujifi lm.com/products/digital_cameras/index.html.
IMPORTANT: Read the following notices before using the camera’s built-in wireless transmitter.
Q This product, which contains encryption function developed in the United States, is controlled by the United States Export Administration Regulations and
may not be exported or re-exported to any country to which the United States embargoes goods.
• Use only as part of a wireless network. FUJIFILM does not accept liability for damages resulting from unauthorized use. Do not use in applications requiring
a high degree of reliability, for example in medical devices or other systems that may directly or indirectly impact human life. When using the device in
computer and other systems that demand a greater degree of reliability than wireless networks, be sure to take all necessary precautions to ensure safety
and prevent malfunction.
• Use only in the country in which the device was purchased. This device conforms to regulations governing wireless network devices in the country in which it was
purchased. Observe all location regulations when using the device. FUJIFILM does not accept liability for problems arising from use in other jurisdictions.
• Wireless data (images) may be intercepted by third parties. The security of data transmitted over wireless networks is not guaranteed.
• Do not use the device in locations subject to magnetic elds, static electricity, or radio interference. Do not use the transmitter in the vicinity of microwave ovens or
in other locations subject to magnetic fi elds, static electricity, or radio interference that may prevent reception of wireless signals. Mutual interference may
occur when the transmitter is used in the vicinity of other wireless devices operating in the 2.4GHz band.
• The wireless transmitter operates in the 2.4GHz band using DSSS and OFDM modulation.
Wireless Network Devices: Cautions
• This device operates on the same frequency as commercial, educational, and medical devices and wireless transmitters. It also operates on the same frequency as
licensed transmitters and special unlicensed low-voltage transmitters used in RFID tracking systems for assembly lines and in other similar applications.
• To prevent interference with the above devices, observe the following precautions. Confi rm that the RFID transmitter is not in operation before using this device.
Should you observe that the device causes interference in licensed transmitters used for RFID tracking, immediately choose a new operating frequency for
this device to prevent additional interference. If you notice that this device causes interference in low-voltage RFID tracing systems, contact a FUJIFILM
representative.
WARNING
Turn the camera o in crowds. The camera emits radio-frequency radiation that may interfere with pacemakers.
Turn the camera o in the vicinity of automatic doors, public address systems, and other automatically controlled devices. The camera emits radio-
frequency radiation that may cause these devices to malfunction.
Keep the camera at least 22cm away from people wearing pacemakers. The camera emits radio-frequency radiation that may interfere with pacemakers.
For Customers in the U.S. A.For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Contains FCC ID :W2Z-02000001Contains FCC ID : W2Z-02000001
Contains IC :W2Z-02000001Contains IC : 7736B-02100001
FCC Statement: This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
CAUTION: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• You are cautioned that any changes or modifi cations not expressly ap-
proved in this manual could void the user’s authority to operate the
equipment.
Notes on the Grant: To comply with Part 15 of the FCC Rules, this product
must be used with a Fujifi lm-specifi ed ferrite-core A/V cable, USB cable, and
DC supply cord.
European Union regulatory noticeEuropean Union regulatory notice
This product complies with the following EU Directives:
• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmo-
nized European standards (European Norms) which are listed on the EU
Declaration of Conformity issued by FUJIFILM Corporation for this product
or product family.
This compliance is indicated by the following conformity marking placed
on the product:
This marking is valid for non-Telecom products and EU harmonized Telecom
products (e.g. Bluetooth).
DA
This document describes cautions on using a wireless transmitter
For more details or other functions, refer to the supplied XP100/XP110 Owner’s Manual or CD-ROM.
Regarding the Declaration of Conformity, visit http://www.fujifi lm.com/products/digital_cameras/index.html.
IMPORTANT: Read the following notices before using the camera’s built-in wireless transmitter.
Q This product, which contains encryption function developed in the United States, is controlled by the United States Export Administration Regulations and
may not be exported or re-exported to any country to which the United States embargoes goods.
• Use only as part of a wireless network. FUJIFILM does not accept liability for damages resulting from unauthorized use. Do not use in applications requiring
a high degree of reliability, for example in medical devices or other systems that may directly or indirectly impact human life. When using the device in
computer and other systems that demand a greater degree of reliability than wireless networks, be sure to take all necessary precautions to ensure safety
and prevent malfunction.
• Use only in the country in which the device was purchased. This device conforms to regulations governing wireless network devices in the country in which it was
purchased. Observe all location regulations when using the device. FUJIFILM does not accept liability for problems arising from use in other jurisdictions.
• Wireless data (images) may be intercepted by third parties. The security of data transmitted over wireless networks is not guaranteed.
• Do not use the device in locations subject to magnetic elds, static electricity, or radio interference. Do not use the transmitter in the vicinity of microwave ovens or
in other locations subject to magnetic fi elds, static electricity, or radio interference that may prevent reception of wireless signals. Mutual interference may
occur when the transmitter is used in the vicinity of other wireless devices operating in the 2.4GHz band.
• The wireless transmitter operates in the 2.4GHz band using DSSS and OFDM modulation.
Wireless Network Devices: Cautions
• This device operates on the same frequency as commercial, educational, and medical devices and wireless transmitters. It also operates on the same frequency as
licensed transmitters and special unlicensed low-voltage transmitters used in RFID tracking systems for assembly lines and in other similar applications.
• To prevent interference with the above devices, observe the following precautions. Confi rm that the RFID transmitter is not in operation before using this device.
Should you observe that the device causes interference in licensed transmitters used for RFID tracking, immediately choose a new operating frequency for
this device to prevent additional interference. If you notice that this device causes interference in low-voltage RFID tracing systems, contact a FUJIFILM
representative.
WARNING
Turn the camera o in crowds. The camera emits radio-frequency radiation that may interfere with pacemakers.
Turn the camera o in the vicinity of automatic doors, public address systems, and other automatically controlled devices. The camera emits radio-
frequency radiation that may cause these devices to malfunction.
Keep the camera at least 22cm away from people wearing pacemakers. The camera emits radio-frequency radiation that may interfere with pacemakers.
For Customers in the U.S. A.For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Contains FCC ID :W2Z-02000001Contains FCC ID : W2Z-02000001
Contains:-IC : 7736B-02100001
FCC Statement: This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
CAUTION: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• You are cautioned that any changes or modifi cations not expressly ap-
proved in this manual could void the user’s authority to operate the
equipment.
Notes on the Grant: To comply with Part 15 of the FCC Rules, this product
must be used with a Fujifi lm-specifi ed ferrite-core A/V cable, USB cable, and
DC supply cord.
European Union regulatory noticeEuropean Union regulatory notice
This product complies with the following EU Directives:
• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmo-
nized European standards (European Norms) which are listed on the EU
Declaration of Conformity issued by FUJIFILM Corporation for this product
or product family.
This compliance is indicated by the following conformity marking placed
on the product:
This marking is valid for non-Telecom products and EU harmonized Telecom
products (e.g. Bluetooth).
NL
This document describes cautions on using a wireless transmitter
For more details or other functions, refer to the supplied XP100/XP110 Owner’s Manual or CD-ROM.
Regarding the Declaration of Conformity, visit http://www.fujifi lm.com/products/digital_cameras/index.html.
IMPORTANT: Read the following notices before using the camera’s built-in wireless transmitter.
Q This product, which contains encryption function developed in the United States, is controlled by the United States Export Administration Regulations and
may not be exported or re-exported to any country to which the United States embargoes goods.
• Use only as part of a wireless network. FUJIFILM does not accept liability for damages resulting from unauthorized use. Do not use in applications requiring
a high degree of reliability, for example in medical devices or other systems that may directly or indirectly impact human life. When using the device in
computer and other systems that demand a greater degree of reliability than wireless networks, be sure to take all necessary precautions to ensure safety
and prevent malfunction.
• Use only in the country in which the device was purchased. This device conforms to regulations governing wireless network devices in the country in which it was
purchased. Observe all location regulations when using the device. FUJIFILM does not accept liability for problems arising from use in other jurisdictions.
• Wireless data (images) may be intercepted by third parties. The security of data transmitted over wireless networks is not guaranteed.
• Do not use the device in locations subject to magnetic elds, static electricity, or radio interference. Do not use the transmitter in the vicinity of microwave ovens or
in other locations subject to magnetic fi elds, static electricity, or radio interference that may prevent reception of wireless signals. Mutual interference may
occur when the transmitter is used in the vicinity of other wireless devices operating in the 2.4GHz band.
• The wireless transmitter operates in the 2.4GHz band using DSSS and OFDM modulation.
Wireless Network Devices: Cautions
• This device operates on the same frequency as commercial, educational, and medical devices and wireless transmitters. It also operates on the same frequency as
licensed transmitters and special unlicensed low-voltage transmitters used in RFID tracking systems for assembly lines and in other similar applications.
• To prevent interference with the above devices, observe the following precautions. Confi rm that the RFID transmitter is not in operation before using this device.
Should you observe that the device causes interference in licensed transmitters used for RFID tracking, immediately choose a new operating frequency for
this device to prevent additional interference. If you notice that this device causes interference in low-voltage RFID tracing systems, contact a FUJIFILM
representative.
WARNING
Turn the camera o in crowds. The camera emits radio-frequency radiation that may interfere with pacemakers.
Turn the camera o in the vicinity of automatic doors, public address systems, and other automatically controlled devices. The camera emits radio-
frequency radiation that may cause these devices to malfunction.
Keep the camera at least 22cm away from people wearing pacemakers. The camera emits radio-frequency radiation that may interfere with pacemakers.
For Customers in the U.S. A.For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Contains FCC ID :W2Z-02000001Contains FCC ID : W2Z-02000001
Contains IC :W2Z-02000001Contains IC : 7736B-02100001
FCC Statement: This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
CAUTION: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• You are cautioned that any changes or modifi cations not expressly ap-
proved in this manual could void the user’s authority to operate the
equipment.
Notes on the Grant: To comply with Part 15 of the FCC Rules, this product
must be used with a Fujifi lm-specifi ed ferrite-core A/V cable, USB cable, and
DC supply cord.
European Union regulatory noticeEuropean Union regulatory notice
This product complies with the following EU Directives:
• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmo-
nized European standards (European Norms) which are listed on the EU
Declaration of Conformity issued by FUJIFILM Corporation for this product
or product family.
This compliance is indicated by the following conformity marking placed
on the product:
This marking is valid for non-Telecom products and EU harmonized Telecom
products (e.g. Bluetooth).
FI
This document describes cautions on using a wireless transmitter
For more details or other functions, refer to the supplied XP100/XP110 Owner’s Manual or CD-ROM.
Regarding the Declaration of Conformity, visit http://www.fujifi lm.com/products/digital_cameras/index.html.
IMPORTANT: Read the following notices before using the camera’s built-in wireless transmitter.
Q This product, which contains encryption function developed in the United States, is controlled by the United States Export Administration Regulations and
may not be exported or re-exported to any country to which the United States embargoes goods.
• Use only as part of a wireless network. FUJIFILM does not accept liability for damages resulting from unauthorized use. Do not use in applications requiring
a high degree of reliability, for example in medical devices or other systems that may directly or indirectly impact human life. When using the device in
computer and other systems that demand a greater degree of reliability than wireless networks, be sure to take all necessary precautions to ensure safety
and prevent malfunction.
• Use only in the country in which the device was purchased. This device conforms to regulations governing wireless network devices in the country in which it was
purchased. Observe all location regulations when using the device. FUJIFILM does not accept liability for problems arising from use in other jurisdictions.
• Wireless data (images) may be intercepted by third parties. The security of data transmitted over wireless networks is not guaranteed.
• Do not use the device in locations subject to magnetic elds, static electricity, or radio interference. Do not use the transmitter in the vicinity of microwave ovens or
in other locations subject to magnetic fi elds, static electricity, or radio interference that may prevent reception of wireless signals. Mutual interference may
occur when the transmitter is used in the vicinity of other wireless devices operating in the 2.4GHz band.
• The wireless transmitter operates in the 2.4GHz band using DSSS and OFDM modulation.
Wireless Network Devices: Cautions
• This device operates on the same frequency as commercial, educational, and medical devices and wireless transmitters. It also operates on the same frequency as
licensed transmitters and special unlicensed low-voltage transmitters used in RFID tracking systems for assembly lines and in other similar applications.
• To prevent interference with the above devices, observe the following precautions. Confi rm that the RFID transmitter is not in operation before using this device.
Should you observe that the device causes interference in licensed transmitters used for RFID tracking, immediately choose a new operating frequency for
this device to prevent additional interference. If you notice that this device causes interference in low-voltage RFID tracing systems, contact a FUJIFILM
representative.
WARNING
Turn the camera o in crowds. The camera emits radio-frequency radiation that may interfere with pacemakers.
Turn the camera o in the vicinity of automatic doors, public address systems, and other automatically controlled devices. The camera emits radio-
frequency radiation that may cause these devices to malfunction.
Keep the camera at least 22cm away from people wearing pacemakers. The camera emits radio-frequency radiation that may interfere with pacemakers.
For Customers in the U.S. A.For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Contains FCC ID :W2Z-02000001Contains FCC ID : W2Z-02000001
ContainsIC: 7736B-02100001
FCC Statement: This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
CAUTION: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• You are cautioned that any changes or modifi cations not expressly ap-
proved in this manual could void the user’s authority to operate the
equipment.
Notes on the Grant: To comply with Part 15 of the FCC Rules, this product
must be used with a Fujifi lm-specifi ed ferrite-core A/V cable, USB cable, and
DC supply cord.
European Union regulatory noticeEuropean Union regulatory notice
This product complies with the following EU Directives:
• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmo-
nized European standards (European Norms) which are listed on the EU
Declaration of Conformity issued by FUJIFILM Corporation for this product
or product family.
This compliance is indicated by the following conformity marking placed
on the product:
This marking is valid for non-Telecom products and EU harmonized Telecom
products (e.g. Bluetooth).
EL
This document describes cautions on using a wireless transmitter
For more details or other functions, refer to the supplied XP100/XP110 Owner’s Manual or CD-ROM.
Regarding the Declaration of Conformity, visit http://www.fujifi lm.com/products/digital_cameras/index.html.
IMPORTANT: Read the following notices before using the camera’s built-in wireless transmitter.
Q This product, which contains encryption function developed in the United States, is controlled by the United States Export Administration Regulations and
may not be exported or re-exported to any country to which the United States embargoes goods.
• Use only as part of a wireless network. FUJIFILM does not accept liability for damages resulting from unauthorized use. Do not use in applications requiring
a high degree of reliability, for example in medical devices or other systems that may directly or indirectly impact human life. When using the device in
computer and other systems that demand a greater degree of reliability than wireless networks, be sure to take all necessary precautions to ensure safety
and prevent malfunction.
• Use only in the country in which the device was purchased. This device conforms to regulations governing wireless network devices in the country in which it was
purchased. Observe all location regulations when using the device. FUJIFILM does not accept liability for problems arising from use in other jurisdictions.
• Wireless data (images) may be intercepted by third parties. The security of data transmitted over wireless networks is not guaranteed.
• Do not use the device in locations subject to magnetic elds, static electricity, or radio interference. Do not use the transmitter in the vicinity of microwave ovens or
in other locations subject to magnetic fi elds, static electricity, or radio interference that may prevent reception of wireless signals. Mutual interference may
occur when the transmitter is used in the vicinity of other wireless devices operating in the 2.4GHz band.
• The wireless transmitter operates in the 2.4GHz band using DSSS and OFDM modulation.
Wireless Network Devices: Cautions
• This device operates on the same frequency as commercial, educational, and medical devices and wireless transmitters. It also operates on the same frequency as
licensed transmitters and special unlicensed low-voltage transmitters used in RFID tracking systems for assembly lines and in other similar applications.
• To prevent interference with the above devices, observe the following precautions. Confi rm that the RFID transmitter is not in operation before using this device.
Should you observe that the device causes interference in licensed transmitters used for RFID tracking, immediately choose a new operating frequency for
this device to prevent additional interference. If you notice that this device causes interference in low-voltage RFID tracing systems, contact a FUJIFILM
representative.
WARNING
Turn the camera o in crowds. The camera emits radio-frequency radiation that may interfere with pacemakers.
Turn the camera o in the vicinity of automatic doors, public address systems, and other automatically controlled devices. The camera emits radio-
frequency radiation that may cause these devices to malfunction.
Keep the camera at least 22cm away from people wearing pacemakers. The camera emits radio-frequency radiation that may interfere with pacemakers.
For Customers in the U.S. A.For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Contains FCC ID :W2Z-02000001Contains FCC ID : W2Z-02000001
Contains IC:7736B-02000001Contains IC : 7736B-02100001
FCC Statement: This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
CAUTION: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• You are cautioned that any changes or modifi cations not expressly ap-
proved in this manual could void the user’s authority to operate the
equipment.
Notes on the Grant: To comply with Part 15 of the FCC Rules, this product
must be used with a Fujifi lm-specifi ed ferrite-core A/V cable, USB cable, and
DC supply cord.
European Union regulatory noticeEuropean Union regulatory notice
This product complies with the following EU Directives:
• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmo-
nized European standards (European Norms) which are listed on the EU
Declaration of Conformity issued by FUJIFILM Corporation for this product
or product family.
This compliance is indicated by the following conformity marking placed
on the product:
This marking is valid for non-Telecom products and EU harmonized Telecom
products (e.g. Bluetooth).
HU
This document describes cautions on using a wireless transmitter
For more details or other functions, refer to the supplied XP100/XP110 Owner’s Manual or CD-ROM.
Regarding the Declaration of Conformity, visit http://www.fujifi lm.com/products/digital_cameras/index.html.
IMPORTANT: Read the following notices before using the camera’s built-in wireless transmitter.
Q This product, which contains encryption function developed in the United States, is controlled by the United States Export Administration Regulations and
may not be exported or re-exported to any country to which the United States embargoes goods.
• Use only as part of a wireless network. FUJIFILM does not accept liability for damages resulting from unauthorized use. Do not use in applications requiring
a high degree of reliability, for example in medical devices or other systems that may directly or indirectly impact human life. When using the device in
computer and other systems that demand a greater degree of reliability than wireless networks, be sure to take all necessary precautions to ensure safety
and prevent malfunction.
• Use only in the country in which the device was purchased. This device conforms to regulations governing wireless network devices in the country in which it was
purchased. Observe all location regulations when using the device. FUJIFILM does not accept liability for problems arising from use in other jurisdictions.
• Wireless data (images) may be intercepted by third parties. The security of data transmitted over wireless networks is not guaranteed.
• Do not use the device in locations subject to magnetic elds, static electricity, or radio interference. Do not use the transmitter in the vicinity of microwave ovens or
in other locations subject to magnetic fi elds, static electricity, or radio interference that may prevent reception of wireless signals. Mutual interference may
occur when the transmitter is used in the vicinity of other wireless devices operating in the 2.4GHz band.
• The wireless transmitter operates in the 2.4GHz band using DSSS and OFDM modulation.
Wireless Network Devices: Cautions
• This device operates on the same frequency as commercial, educational, and medical devices and wireless transmitters. It also operates on the same frequency as
licensed transmitters and special unlicensed low-voltage transmitters used in RFID tracking systems for assembly lines and in other similar applications.
• To prevent interference with the above devices, observe the following precautions. Confi rm that the RFID transmitter is not in operation before using this device.
Should you observe that the device causes interference in licensed transmitters used for RFID tracking, immediately choose a new operating frequency for
this device to prevent additional interference. If you notice that this device causes interference in low-voltage RFID tracing systems, contact a FUJIFILM
representative.
WARNING
Turn the camera o in crowds. The camera emits radio-frequency radiation that may interfere with pacemakers.
Turn the camera o in the vicinity of automatic doors, public address systems, and other automatically controlled devices. The camera emits radio-
frequency radiation that may cause these devices to malfunction.
Keep the camera at least 22cm away from people wearing pacemakers. The camera emits radio-frequency radiation that may interfere with pacemakers.
For Customers in the U.S. A.For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Contains FCC ID :W2Z-02000001Contains FCC ID : W2Z-02000001
ContainsIiIC: 7736B-02100001
FCC Statement: This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
CAUTION: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• You are cautioned that any changes or modifi cations not expressly ap-
proved in this manual could void the user’s authority to operate the
equipment.
Notes on the Grant: To comply with Part 15 of the FCC Rules, this product
must be used with a Fujifi lm-specifi ed ferrite-core A/V cable, USB cable, and
DC supply cord.
European Union regulatory noticeEuropean Union regulatory notice
This product complies with the following EU Directives:
• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmo-
nized European standards (European Norms) which are listed on the EU
Declaration of Conformity issued by FUJIFILM Corporation for this product
or product family.
This compliance is indicated by the following conformity marking placed
on the product:
This marking is valid for non-Telecom products and EU harmonized Telecom
products (e.g. Bluetooth).
IT
This document describes cautions on using a wireless transmitter
For more details or other functions, refer to the supplied XP100/XP110 Owner’s Manual or CD-ROM.
Regarding the Declaration of Conformity, visit http://www.fujifi lm.com/products/digital_cameras/index.html.
IMPORTANT: Read the following notices before using the camera’s built-in wireless transmitter.
Q This product, which contains encryption function developed in the United States, is controlled by the United States Export Administration Regulations and
may not be exported or re-exported to any country to which the United States embargoes goods.
• Use only as part of a wireless network. FUJIFILM does not accept liability for damages resulting from unauthorized use. Do not use in applications requiring
a high degree of reliability, for example in medical devices or other systems that may directly or indirectly impact human life. When using the device in
computer and other systems that demand a greater degree of reliability than wireless networks, be sure to take all necessary precautions to ensure safety
and prevent malfunction.
• Use only in the country in which the device was purchased. This device conforms to regulations governing wireless network devices in the country in which it was
purchased. Observe all location regulations when using the device. FUJIFILM does not accept liability for problems arising from use in other jurisdictions.
• Wireless data (images) may be intercepted by third parties. The security of data transmitted over wireless networks is not guaranteed.
• Do not use the device in locations subject to magnetic elds, static electricity, or radio interference. Do not use the transmitter in the vicinity of microwave ovens or
in other locations subject to magnetic fi elds, static electricity, or radio interference that may prevent reception of wireless signals. Mutual interference may
occur when the transmitter is used in the vicinity of other wireless devices operating in the 2.4GHz band.
• The wireless transmitter operates in the 2.4GHz band using DSSS and OFDM modulation.
Wireless Network Devices: Cautions
• This device operates on the same frequency as commercial, educational, and medical devices and wireless transmitters. It also operates on the same frequency as
licensed transmitters and special unlicensed low-voltage transmitters used in RFID tracking systems for assembly lines and in other similar applications.
• To prevent interference with the above devices, observe the following precautions. Confi rm that the RFID transmitter is not in operation before using this device.
Should you observe that the device causes interference in licensed transmitters used for RFID tracking, immediately choose a new operating frequency for
this device to prevent additional interference. If you notice that this device causes interference in low-voltage RFID tracing systems, contact a FUJIFILM
representative.
WARNING
Turn the camera o in crowds. The camera emits radio-frequency radiation that may interfere with pacemakers.
Turn the camera o in the vicinity of automatic doors, public address systems, and other automatically controlled devices. The camera emits radio-
frequency radiation that may cause these devices to malfunction.
Keep the camera at least 22cm away from people wearing pacemakers. The camera emits radio-frequency radiation that may interfere with pacemakers.
For Customers in the U.S. A.For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Contains FCC ID :W2Z-02000001Contains FCC ID : W2Z-02000001
ContainsIC: 7736B-02100001
FCC Statement: This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
CAUTION: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• You are cautioned that any changes or modifi cations not expressly ap-
proved in this manual could void the user’s authority to operate the
equipment.
Notes on the Grant: To comply with Part 15 of the FCC Rules, this product
must be used with a Fujifi lm-specifi ed ferrite-core A/V cable, USB cable, and
DC supply cord.
European Union regulatory noticeEuropean Union regulatory notice
This product complies with the following EU Directives:
• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmo-
nized European standards (European Norms) which are listed on the EU
Declaration of Conformity issued by FUJIFILM Corporation for this product
or product family.
This compliance is indicated by the following conformity marking placed
on the product:
This marking is valid for non-Telecom products and EU harmonized Telecom
products (e.g. Bluetooth).
LT
This document describes cautions on using a wireless transmitter
For more details or other functions, refer to the supplied XP100/XP110 Owner’s Manual or CD-ROM.
Regarding the Declaration of Conformity, visit http://www.fujifi lm.com/products/digital_cameras/index.html.
IMPORTANT: Read the following notices before using the camera’s built-in wireless transmitter.
Q This product, which contains encryption function developed in the United States, is controlled by the United States Export Administration Regulations and
may not be exported or re-exported to any country to which the United States embargoes goods.
• Use only as part of a wireless network. FUJIFILM does not accept liability for damages resulting from unauthorized use. Do not use in applications requiring
a high degree of reliability, for example in medical devices or other systems that may directly or indirectly impact human life. When using the device in
computer and other systems that demand a greater degree of reliability than wireless networks, be sure to take all necessary precautions to ensure safety
and prevent malfunction.
• Use only in the country in which the device was purchased. This device conforms to regulations governing wireless network devices in the country in which it was
purchased. Observe all location regulations when using the device. FUJIFILM does not accept liability for problems arising from use in other jurisdictions.
• Wireless data (images) may be intercepted by third parties. The security of data transmitted over wireless networks is not guaranteed.
• Do not use the device in locations subject to magnetic elds, static electricity, or radio interference. Do not use the transmitter in the vicinity of microwave ovens or
in other locations subject to magnetic fi elds, static electricity, or radio interference that may prevent reception of wireless signals. Mutual interference may
occur when the transmitter is used in the vicinity of other wireless devices operating in the 2.4GHz band.
• The wireless transmitter operates in the 2.4GHz band using DSSS and OFDM modulation.
Wireless Network Devices: Cautions
• This device operates on the same frequency as commercial, educational, and medical devices and wireless transmitters. It also operates on the same frequency as
licensed transmitters and special unlicensed low-voltage transmitters used in RFID tracking systems for assembly lines and in other similar applications.
• To prevent interference with the above devices, observe the following precautions. Confi rm that the RFID transmitter is not in operation before using this device.
Should you observe that the device causes interference in licensed transmitters used for RFID tracking, immediately choose a new operating frequency for
this device to prevent additional interference. If you notice that this device causes interference in low-voltage RFID tracing systems, contact a FUJIFILM
representative.
WARNING
Turn the camera o in crowds. The camera emits radio-frequency radiation that may interfere with pacemakers.
Turn the camera o in the vicinity of automatic doors, public address systems, and other automatically controlled devices. The camera emits radio-
frequency radiation that may cause these devices to malfunction.
Keep the camera at least 22cm away from people wearing pacemakers. The camera emits radio-frequency radiation that may interfere with pacemakers.
For Customers in the U.S. A.For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Contains FCC ID :W2Z-02000001Contains FCC ID : W2Z-02000001
-0200000IC: 7736B-02100001
FCC Statement: This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
CAUTION: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• You are cautioned that any changes or modifi cations not expressly ap-
proved in this manual could void the user’s authority to operate the
equipment.
Notes on the Grant: To comply with Part 15 of the FCC Rules, this product
must be used with a Fujifi lm-specifi ed ferrite-core A/V cable, USB cable, and
DC supply cord.
European Union regulatory noticeEuropean Union regulatory notice
This product complies with the following EU Directives:
• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmo-
nized European standards (European Norms) which are listed on the EU
Declaration of Conformity issued by FUJIFILM Corporation for this product
or product family.
This compliance is indicated by the following conformity marking placed
on the product:
This marking is valid for non-Telecom products and EU harmonized Telecom
products (e.g. Bluetooth).
XP170BL01731.indd1
2012/04/0511:20:24
FCC ID:W2Z-02100001
IC:7736B-02100001
FCC ID:W2Z-02100001
IC:7736B-02100001
FCC ID:W2Z-02100001
IC:7736B-02100001
FCC ID:W2Z-02100001
IC:7736B-02100001
FCC ID:W2Z-02100001
IC:7736B-02100001
FCC ID:W2Z-02100001
IC:7736B-02100001
FCC ID:W2Z-02100001
IC:7736B-02100001
FCC ID:W2Z-02100001
IC:7736B-02100001
FCC ID:W2Z-02100001
IC:7736B-02100001
To Next Page
Need help?
General
Weight and Dimensions
