What to do if my Fujitsu Air Conditioner remote is not working due to a communication error?
If you're experiencing a Wired Remote Controller Communication Error with your Fujitsu Air Conditioner, check the voltage. If it's DC12V, the remote control has failed and should be replaced. If it's DC 0V, the Controller PCB has failed and should be replaced after rechecking the remote control.
What to do if my Fujitsu Air Conditioner has a drainage error?
If your Fujitsu Air Conditioner is experiencing drainage issues, start by inspecting the float switch for proper operation using a meter to check its on/off switching. If the float switch is defective, replace it. Also, examine the drain hose for any clogs and clear them if necessary. If these steps don't resolve the issue, consider replacing the controller PCB.
How to fix a Fujitsu AGU12RLF Air Conditioner indoor unit fan motor error?
If you're encountering an indoor unit fan motor error with your Fujitsu Air Conditioner, check first the fan and bearing. If either is damaged, replace them. If the motor itself is faulty, replace the indoor unit fan motor. If these steps do not resolve the issue, replace the controller PCB.
What to do if my Fujitsu AGU12RLF Air Conditioner shows an indoor room thermistor error?
If your Fujitsu Air Conditioner displays an indoor room thermistor error, begin by checking the connector to ensure it is securely attached and properly connected, and verify that the thermistor cable is not open. If the thermistor is either open or shorted, replace it and then reset the power.
How to troubleshoot an Indoor Unit Model Information Error on my Fujitsu Air Conditioner?
If your Fujitsu Air Conditioner is showing an Indoor Unit Model Information Error, check for external causes such as noise and ensure the ground connection is properly connected. Also, inspect all connectors for looseness or incorrect wiring, and check the PCB for any shorts or corrosion. If the problem persists, consider replacing the Controller PCB.
What does an Indoor Unit Capacity Error mean on my Fujitsu AGU12RLF?
If your Fujitsu Air Conditioner is showing an Indoor Unit Capacity Error, first verify the total capacity of the connected indoor units. If an abnormal condition is found, correct it by referring to the Installation Manual or Design & Technical Manual. If the problem persists, replace the Main PCB of the Outdoor unit.
How to fix a Serial Communication Error (Serial Reverse Transfer Error) on a Fujitsu Air Conditioner?
If your Fujitsu Air Conditioner displays a Serial Communication Error (Serial Reverse Transfer Error), check all connection lines between the indoor and outdoor units for any looseness or disconnections, referring to the Installation Manual or Data & Technical Manual for correction. Also, check the voltage of the power supply, ensuring it appears at the outdoor unit terminal L1 - L2 within the range of AC187V - 253V. Check that the indicated value swings between AC90V and AC270V at outdoor unit terminal 1 - 3. If the outdoor fan motor, active filter module, or IPM is abnormal, replace the corresponding part. If all parts are normal, replace the Main PCB.
How to resolve a Damper (Open/Close) simultaneous detection Limit switch error on a Fujitsu AGU12RLF Air Conditioner?
If your Fujitsu Air Conditioner displays a Damper(Open/Close) simultaneous detection Limit switch error, replace the limit switch if it is defective. If the problem persists, replace the Controller PCB.
Explains compressor frequency determination based on temperature and unit settings.
Details automatic switching between Heating, Cooling, Dry, and Monitoring modes based on temperature.
Covers indoor fan speed settings, airflow modes, and adjustments for various operations.
Explains vertical and horizontal louver adjustments, swing operations, and their settings.
Shows fan speeds for outdoor units in Cooling and Heating modes.
Details compressor operation frequency ranges and control strategies during start-up.
Explains wireless remote controller timer settings: ON/OFF, Program, and Sleep timers.
Describes pulse ranges for electronic expansion valve control based on operation mode and temperature.
Outlines procedures for test run operations using wireless and wired remote controllers.
Explains the 3-minute delay mechanism before the compressor restarts after a stop.
Details the 3-minute delay for 4-way valve switching when changing from Cooling to Heating mode.
Describes how operation contents are memorized and resumed automatically after a power interruption.
Explains manual auto operation mode for use without a remote control or in emergencies.
Details the process of heating the compressor to prevent damage in low ambient temperatures.
Explains the powerful operation mode for maximum indoor/outdoor unit output.
Describes the minimum heat operation performance when activating the MIN. HEAT button.
Explains the economy operation for reduced output, saving energy in cooling and heating.
Setting to improve room temperature control suitability for buildings with high insulation.
Details thermo control operation and compressor cycles based on the indoor unit sensor.
Details thermo control operation and compressor cycles based on the wired remote sensor.
Describes the base heater operation conditions and controls, primarily for heating.
Explains the synchronization of the fresh air fan with indoor fan operation for air circulation.
Details the conditions and operation of the external electrical heater.
Explains drain pump operation cycles during Cooling/Dry and Heating/Fan modes.
Details how to set air outlets for upper/lower airflow or upper airflow only.
Explains conditions for starting, integrating, and completing defrost operation based on temperatures.
Procedure for check run and automatic wiring correction to verify and correct unit connections.
Details protections like Discharge Gas Temperature Over Rise, Current Release, and Cooling Pressure Over Rise.
Procedure for pump down operation when moving or discarding the air conditioner unit.
Method for performing test runs on the outdoor unit to check its operation and components.
Lists error contents, indoor unit display patterns, and corresponding troubleshooting steps.
Provides detailed troubleshooting steps for specific error codes, starting with Serial Communication Error.
Guides on diagnosing issues like "No Power" without specific error codes.
Lists service parts and their diagnostic procedures, including Compressor, Fan Motor, and PCBs.
General| Power Supply | 220-240V, 50Hz |
|---|---|
| Refrigerant | R410A |
| Indoor Unit Dimensions (WxHxD) | 790 x 275 x 202 mm |
| Outdoor Unit Dimensions (WxHxD) | 660 x 530 x 240 mm |
| Indoor Unit Weight | 9 kg |
| Energy Efficiency Ratio (EER) | 11 BTU/W |
| Indoor Unit Noise Level | 21 dB |
| Cooling Capacity | 12000 BTU/h |
To Next Page