En-9
The frequency of the cleaning is as shown in the following table.
What to do Frequency
Indoor unit body Cleaning When you notice
Air lter Cleaning Every 2 weeks
Apple-catechin lter (UTR-FA16) Replacing Every 3 months
(White)
Ion deodorization lter (UTR-FA16-2) Cleaning Every 3 months
(Light blue)
Replacing Every 3 years
* The air cleaning lters are sold separately. When you replace them,
contact the store of purchase.
Cleaning indoor unit body
NOTES:
• Do not use water hotter than 40 °C.
• Do not use scouring cleanser, volatile solvents such as benzene or
thinner.
1. Wipe the indoor unit body gently with a soft cloth moisten
with warm water.
2. Wipe the indoor unit body gently with a dry and soft cloth.
Cleaning air lter
1. Open the intake grille until it snaps.
2. Remove the air lters.
Lift up the air lters' handle, disconnect the two lower tabs, and pull
out.
Air Filter handle
Tabs (2 places)
3. Remove the dust in either of the following ways.
• Cleaning with vacuum cleaner.
• Washing with mild detergent and warm water. After washing, dry the
air lters thoroughly in shade.
4. Replace the air lters.
Align the sides of the air lter with the panel, and push in fully.
Make sure to the two lower tabs are returned to their holes in the
indoor unit properly.
5. Close the intake grille.
Press 4 places on the intake grille to close it completely.
NOTE: If dirt accumulates on the air lter, airow will be reduced,
operating eciency will lower, and the noise will increase.
9. SETTINGS ON INSTALLATION
9.1. Remote controller custom code setting
By setting custom code of indoor unit and remote controller, you can
specify the air conditioner which the remote controller controls.
When two or more air conditioners are in the room and you wish to
operate them separately, set the custom code (4 selections possible).
NOTE: If custom codes is dierent between the indoor unit and the
remote controller, the indoor unit cannot receive a signal from
the remote controller.
How to set the remote controller custom code
1. Press
until only the clock is displayed on the remote
controller display.
2. Press and hold
for more than
5 seconds.
The current custom code will be
displayed (initially set to A).
3. Press
to change the
custom code between A (
) ↔ B ( )
↔ C (
) ↔ D ( ).
* Match the custom code on the display
to the air conditioner custom code.
4. Press
again.
The custom code will be set.
The display will return to the clock display.
• To change the air conditioner custom code, contact authorized
service personnel (initially set to A).
• If you do not press any buttons for 30 seconds after the custom
code is displayed, the display returns to the clock display. In this
case, repeat the setting from step 2.
• Depending on the remote controller, the custom code may return
to A when replacing the batteries. In this case, reset the custom
code as necessary. If you do not know the air conditioner custom
code, try each code until you nd the code which operates the air
conditioner.
10. CLEANING AND CARE
CAUTION
• Before cleaning this product, be sure to turn it o and
disconnect all the power supply.
• Before starting operation, make sure that the intake
grille has been shut completely. Incomplete closing
of the intake grille might have an eect on the proper
working or performance of the air conditioner.
• If the lter cleaning involves high-place work, consult
authorized service
personnel.
• Do not touch the aluminum ns of heat exchanger
built-in the indoor unit to avoid personal injury when
you maintain the unit.
• Do not expose the indoor unit to liquid insecticides or
hair sprays.
• Do not stand on slippery, uneven or unstable surfaces
when you maintain the unit.
Intake grille
Air lters
Indoor unit body
Air cleaning lters
(Apple catechin lter, Ion deodorization lter)
9387602296-01_OM.indb 99387602296-01_OM.indb 9 17-Feb-22 14:56:0617-Feb-22 14:56:06
To Next Page
Loading...
Need help?
General
