Fujitsu FO2416RTJNAA - Page 10

10
4.2 Choosing a Location (cont.)
4.2.3 Corrosive Environment
The metal parts of this unit may be subject to
rust or deterioration if exposed to a corrosive
environment. This oxidation could shorten the
HTXLSPHQW·VXVHIXOOLIH
Corrosive elements include, but are not limited to,
salt spray, fog or mist in seacoast areas, sulphur or
FKORULQHIURPODZQZDWHULQJV\VWHPVDQGYDULRXV
chemical contaminants from industries such as
paper mills and petroleum refineries.
,IWKHXQLWLVWREHLQVWDOOHGLQDQDUHDZKHUH
FRQWDPLQDQWVDUHOLNHO\WREHDSUREOHPVSHFLDO
attention should be given to the equipment location
and exposure.
$YRLGKDYLQJODZQVSULQNOHUKHDGVVSUD\GLUHFWO\
on the unit cabinet.
• In coastal areas, locate the unit on the side of the
EXLOGLQJDZD\IURPWKHZDWHUIURQW
• Shielding provided by a fence or shrubs may give
some protection, but cannot violate minimum
DLUIORZDQGVHUYLFHDFFHVVFOHDUDQFHV
WARNING: 'LVFRQQHFWDOOSRZHU
to unit before starting maintenance. Failure to do
VRFDQFDXVHHOHFWULFDOVKRFNUHVXOWLQJLQVHYHUH
personal injury or death.
5HJXODUPDLQWHQDQFHZLOOUHGXFHWKHEXLOGXSRI
FRQWDPLQDQWVDQGKHOSWRSURWHFWWKHXQLW·VILQLVK
)UHTXHQWZDVKLQJRIWKHFDELQHWIDQEODGHDQG
FRLOZLWKIUHVKZDWHUZLOOUHPRYHPRVWRIWKHVDOW
or other contaminants that build up on the unit.
5HJXODUFOHDQLQJDQGZD[LQJRIWKHFDELQHW
ZLWKDJRRGDXWRPRELOHSROLVKZLOOSURYLGHVRPH
protection.
• A good liquid cleaner may be used several times
D\HDUWRUHPRYHPDWWHUWKDWZLOOQRWZDVKRIIZLWK
ZDWHU
4.2.4 Customer Satisfaction
Issues
7KHKHDWSXPSVKRXOGEHORFDWHGDZD\IURPWKH
living, sleeping, and recreational spaces of the
RZQHUDQGWKRVHVSDFHVRQDGMRLQLQJSURSHUW\
• To prevent noise transmission, the mounting pad
for the outdoor unit should not be connected to
the structure and should be located a sufficient
GLVWDQFHDERYHJUDGHWRSUHYHQWJURXQGZDWHU
from entering the unit.
4.0 INSTALLATION
4.3.1 Unit Mounting Methods
The outdoor heat pump unit may be mounted in
DQXPEHURIZD\V7KHPRVWFRPPRQPHWKRGLV
on a ground mounted concrete or pre-fabricated
pad. It can also be mounted on a ground or roof
PRXQWHGPHWDOIUDPHZRRGHQIUDPHRUµ[µ
ZRRGHQVWULQJHUV,WLVH[WUHPHO\LPSRUWDQWWR
properly secure the unit to the pad or frame so it
GRHVQRWVKLIWGXULQJKLJKZLQGVVHLVPLFHYHQWV
or other outside forces to eliminate the possibility
of a safety hazard or physical damage to the
unit. Local codes in regions subject to frequent
KXUULFDQHVDQGVHLVPLFHYHQWVZLOOGLFWDWHVSHFLILF
PRXQWLQJUHTXLUHPHQWVDQGPXVWEHIROORZHG,W
is also important to elevate the heat pump in areas
WKDWUHFHLYHDVLJQLILFDQWDPRXQWRIVQRZIDOOVR
DFFXPXODWHGVQRZGRHVQRWEORFNWKHRXWGRRUFRLO
DQGLQWHUIHUHZLWKGUDLQDJHRIZDWHUGXULQJWKH
defrost cycle. Refer to Section 4.3.4 for typical
JURXQGVQRZOHYHOVIRUGLIIHUHQWUHJLRQVRIWKH86$
4.3.2 High Wind and Seismic
Tie-Down Methods
The manufacturer-approved/recommended method
LVDJXLGHWRVHFXULQJHTXLSPHQWIRUZLQGDQG
seismic loads. Other methods might provide the
same result, but the manufacturer method is the
only one endorsed by the manufacturer for securing
HTXLSPHQWZKHUHZLQGRUHDUWKTXDNHGDPDJH
can occur. Additional information is available on
WKHPDQXIDFWXUHU·VZHEVLWHRUIURPWKHZKROHVDOH
distributor.
4.3
Location