To Next PageTo Next PageHow to fix a Fujitsu Lifebook T731 Laptop that will not start?
If your Fujitsu Laptop won't start, there could be a few reasons. First, ensure the battery is correctly installed in its compartment. If it is, the battery might be dead, so try charging it, inserting a charged battery, or connecting the mains adapter. Finally, verify that the power adapter is correctly connected to the laptop.
Why does my Fujitsu Lifebook T731 battery drain so fast?
There are several reasons why your Fujitsu Laptop battery might be discharging quickly. The battery could be too hot or too cold (the battery indicator will flash in this case); bring the laptop to a normal temperature. An application might be consuming a lot of power by frequently accessing the hard disk or optical drive; use the mains adapter as frequently as possible. The screen brightness may be set too high; decrease the screen brightness using the key combination to reduce power consumption. If the operating time of the battery life is extremely short, the battery is probably too old and needs to be replaced.
What to do if my Fujitsu Lifebook T731 suddenly stops working?
If your Fujitsu Laptop stops working, it could be due to a few reasons. It might be in energy-saving mode, so leave energy-saving mode. An application program might have caused the malfunction; close the application program or restart the laptop. The battery might be dead; charge the battery, insert a charged battery, or connect the mains adapter to the laptop.
How do I fix a blank external monitor connected to my Fujitsu Lifebook T731 Laptop?
If your external monitor remains blank when connected to your Fujitsu Laptop, check the following: Ensure the monitor is switched on. Press any key to continue in case power saving has been activated. Adjust the brightness of the monitor if it is set too low. Check if the screen output is set to the notebook’s LCD screen. Ensure the power cable and data cable are properly connected to both the monitor and the laptop. To do this, switch off the external monitor and the laptop, check the cable connections, and then switch them back on.
What to do if my Fujitsu Lifebook T731 Laptop screen is blank?
If your Fujitsu Laptop's LCD screen remains blank, try the following: Press a key or touch the touchpad in case the monitor is switched off. If you have an external monitor or television set connected, press the key combination to switch the screen output.
Why is my Fujitsu Laptop not connecting to Wi-Fi?
If the wireless connection on your Fujitsu Laptop is not working, it could be because the wireless component is disabled. Switch the radio component on. If the wireless component is enabled but the connection still doesn't work, check whether the radio connection is switched on via the software. Further information on using the radio component can be found in the help files.
How to fix 'System CMOS checksum bad' error on Fujitsu Lifebook T731 Laptop?
If you receive the error message 'System CMOS checksum bad - default configuration used' on your Fujitsu Laptop, it indicates that the system configuration information is incorrect. To resolve this, switch the notebook off, then switch it back on. Press the function key F2 to access the BIOS Setup. In the BIOS Setup, select the Exit menu. Select the entry Load Setup Defaults, select OK, and press the Enter key.
What to do if my Fujitsu Tablet PC does not turn on when installed in the optional Port Replicator?
If your Tablet PC isn't turning on when docked, ensure the Port Replicator AC adapter is plugged in to provide power. Also, make sure the Tablet PC is properly seated in the Port Replicator by removing and re-docking it.
What to do if my Fujitsu Tablet PC will not work on battery alone?
If your Tablet PC isn't working on battery, replace the battery with a charged one or install a power adapter, if the installed battery is dead. If no battery is installed, install a charged battery. Verify that the battery is properly connected by re-installing it, if the battery is improperly installed.
How to fix a dark display on battery power on Fujitsu Tablet PC?
If the display is dark when on battery power, it may be because the Power Management utility is set to low brightness to conserve power. Press [Fn] + [F7] to increase brightness or click the battery gauge, click on More power options, and select Adjust the display brightness.
General| Display Size | 12.1 inches |
|---|---|
| Storage | 500 GB HDD |
| Display Resolution | 1366 x 768 pixels |
| Graphics | Intel HD Graphics |
| Operating System | Windows 8 Pro |
| Battery Life | Up to 8 hours |
| Connectivity | Wi-Fi, Bluetooth |
| Ports | USB 3.0, USB 2.0, VGA, HDMI, Ethernet |
