Fulling DZB200M - Overload and Protection Fault Diagnosis; Unit Protection Fault Diagnosis

Correctly set up the parameter
Reducetheloador
increase the inverter capacity
T he moto r pro tecti on parameter
F5.01 setting is suitable or not
Theloadistoobigorthemotorisblocked
The t ype of in ver ter is s ma ll
No
Yes
Yes
No
Theloadistoobigorthemotorisblocked
The t ype of in ver ter is s ma ll
Reducetheloador
increase the inverter capacity
Yes
No
9.Inverse unit protec tion (E009 E019 E029) 、、
Remove the periphe ral fault
In st al l th e re ac t o r or
output w ave-filter
Check if the wind channel is
blocked or the fan is working
normally and r emove the problem
Plug all the lin ks
Invers e m odule da mage
Ch eck if t he o utp ut lo op of t he m otor
driverinverterhas th e ea rthing
or short circuit
Whe ther thelink betwee n the motor
andthemotordriverinverteristoolong
W het h er the m od u le is overhe ated
Whether the drive board is normal
after renewal
Check if the internal links of
the motor driver inverter are lo ose
Whether i t is normal after the
renewal of the main con trol board
Wh ether the in ve r se mod ule
is normal after renewal
driveboard fault
ma in cont ro l board faul t
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
Seek technical s upp or t
Ad ju s t t he volt a ge with i n
n ormal range
Cancel the externalforceor
inst a ll the brak e r esi stor
Increase the acceleration time
or install the brake resistor
Install the brake resistor
The inpu t vol tage is too high o r n ot
If there exists external f orces driving the
motor operation during the deceleration process
The decelerat ion time is to o sho rt or not
I sthere a ny brake r esistor in stalled
Yes
Yes
Yes
No
No
No
No
Yes
Se ek techn i ca l supp ort
7.Motor Over Load(E 007)
8.InverterOver Load(E008)
12. Diode ModuleOver Heat(E00E)
10. Overvoltage during deceleration(E00A)
Reduce t he environmental
temperature
Clear the windchannel
If the environmental t emperature is toohigh
If the wind channel is blocked
Yes
Yes
No
No
If the fan is da mage d
No
If the modular heat-variable resistor is damaged
Yes
Yes
Change the fan
Changethe heatvariable
resistor
Changetheinverse modul e
No
If the inverse mo dule is da maged
Yes
Seekfor thetechnical support
Chapter 7 Fault D iagnosis and Co untermeasures
DZB Series
Chapter 7 Fault Dia gnosis and Co untermeasure s
DZB S eri es
Reset running
Check andremove
peripheral fault
Press STOP button to stopin the
nonkeyb oard opera tion mode or not
I nput perip he ral faul t signal vi a
multif unctional terminal DI or no t
Yes
Yes
No
No
Use ST OP in s tall
Yes
Reset running
11 . E xternal Failure(E00D)
-75-
-76-
BLUE ELEPHANT BLUE ELEPHANT BLUE ELEPHANT BLUE ELEPHANT
BLUE ELEPHANT BLUE ELEPHANT BLUE ELEPHANT BLUE ELEPHANT
BLUE ELEPHANT BLUE ELEPHANT BLUE ELEPHANT BLUE ELEPHANT
BLUE ELEPHANT BLUE ELEPHANT BLUE ELEPHANT BLUE ELEPHANT
BLUE ELEPHANT BLUE ELEPHANT BLUE ELEPHANT BLUE ELEPHANT
BLUE ELEPHANT BLUE ELEPHANT BLUE ELEPHANT BLUE ELEPHANT