Fusion CRGBW User Manual

Display mode 14 Red, green, blue, yellow, teal, magenta, and full
white strobe
Display mode 15 Full white flash
Display mode 16 Cool white flash
Display mode 17 Warm white flash
Display mode 18 Cool white and warm white flash
Display mode 19 Red, cool white, and warm white flash
Display mode 20 Green, cool white, and warm white flash
Display mode 21 Blue, cool white, and warm white flash
Display mode 22 Red, green, blue, cool white, and warm white flash
Display mode 23 Red, green, blue, yellow, teal, magenta, full white,
cool white, and warm white flash
Display mode 24 Full white, cool white, and warm white flash
Display mode 25 Automatically cycles all 24 display modes
Changing the Speed of a Display Mode Pattern
You can adjust the speed of the effects when using a display-
mode pattern.
1
If necessary, turn on the LEDs for the speakers.
2
If necessary, select a the display mode (Changing the
Display Mode of the LEDs, page 2).
3
Select an option:
• To increase the speed of the display-mode-pattern effect,
press above .
• To decrease the speed of the display-mode-pattern effect,
press below .
Unpairing a Remote Control from the Wireless
Receiver
You can unpair a remote control from the wireless receiver if you
are planning to replace it.
1
If necessary, install the wireless receiver, and connect it to
the speaker LEDs (Connecting the Remote Control Receiver,
page 1).
2
If necessary, install batteries in the replacement remote
control (Installing the Batteries, page 2).
3
Disconnect the power from the wireless receiver.
4
Hold on the remote control, and connect the wireless
receiver to power.
The LEDs flash nine times to indicate that the remote control
is unpaired from the wireless receiver.
NOTE: After the remote control is unpaired from the wireless
receiver, the connected LEDs fade in and out through a red,
green, and blue cycle until you pair a new remote control with
the wireless receiver (Pairing a Remote Control with the
Wireless Receiver, page 3).
Pairing a Remote Control with the Wireless Receiver
If you replace a lost or damaged remote control with a new
remote control, you can use the replacement remote control with
an existing wireless receiver.
1
If necessary, install the wireless receiver and connect it to the
speaker LEDs (Connecting the Remote Control Receiver,
page 1).
2
If necessary, install batteries in the replacement remote
control (Installing the Batteries, page 2).
3
Disconnect the power from the wireless receiver.
4
Hold on the remote control, and connect the wireless
receiver to power.
The LEDs flash three times to indicate that the remote control
is paired to the wireless receiver.
Specifications
Input voltage 10.8 to 16 Vdc
Fuse 7.5 A
Max. capacity Up to 10 CRGBW LED speakers (5 pair)
Operating temperature From 0 to 50°C (32 to 122°F)
Storage temperature From -20 to 70°C (-4 to 158°F)
Battery type 2 AAA (not included)
Radio frequency 2.4 GHz @ 10 dBm nominal
Range Up to 10 m (30 ft.)
Water rating Remote control receiver and remote control are
not water or dust resistant.
Registering Your Wireless CRGBW LED Remote
Control
Help us better support you by registering the product online.
• Go to www.fusionentertainment.com.
• Keep the sales receipt, or a copy, in a safe place.
© 2020 Garmin Ltd. or its subsidiaries
Garmin
®
, the Garmin logo, Fusion
®
, and the Fusion logo, are trademarks of Garmin Ltd.
or its subsidiaries, registered in the USA and other countries. These trademarks may not
be used without the express permission of Garmin.
Wireless CRGBW LED Remote Control Instructions 3

Fusion CRGBW Specifications

General

Brand	Fusion
Model	CRGBW
Category	Remote Control
Language	English