EasyManua.ls Logo

FUTABA T26SZ - Page 219

FUTABA T26SZ
248 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
219
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
GyrosettingCGY770RGyrosettingCGY770R
GovernorExpert
GovernorExpert
7KLVPHQXVHWVWKH*RYHUQRU([SHUWSDUDPHWHUVDOORZLQJWKHXVHUWRIXUWKHUUH¿QHWKHJRYHUQRUVHWWLQJV
"Governor Expert" screen from the "EXPERT MENU 3D" screen.
(1) Work Mode: Governor working mode
Setsthegoverningtypemode.
-GOVERNOR(GovernorMode) ‒RPM isentirelycontrolledbytheGOV
onceithasengaged. TheGOVwill dowhateverittakestoholdacon
-
stantRPMthroughoutflight.
-Rev.Lmt(LimiterMode)‒Throttlecontrolfollowsthethrottlecurvesto
advancethethrottlepositionduringflight,butcontrolstheRPMduring
throttlereductionbynotlettingtheRPMoverspeedpastthesetRPM.
WhentheRev.Lmtmodeisselected,themenu(5)"THR.Mode"shouldbe
settoTx.Curvemode.
Setting:GOVERNOR/Rev.LmtInitialsetting:GOVERNOR
(2) Revo Disp: Governor working mode
ThisenablestheusertodisplayeitherthedesiredrotorRPMortheEn-
gineRPMaccordingly.
Setting:Rotor/EngineInitialsetting:Rotor
(3) F/F. Cyclic: Feed Forward from Cyclic
IncreasingthevaluewilladdthrottlewithcycliccommandstoaidinRPM
stability.
Settingranges:0~100%Initialvalue:0%
(5) THR. Mode: Throttle data mode
Thisparameterselectsthethrottleinputoperation.
Optimize:
CGYsetsthethrottleinputsignaltooptimum.Thereisnoneedtoconsider
thethrottlecurvesettingonthetransmitter.
Fixed:
Thisisthesuggestedmodeforusewithelectricmotors.Thissettingensures
thatthereisafixedthrottleinputasisrelatedtothehelicopterrevolution.
Tx.Curve:
Ifthismodeisselected,theCGYusestheexactthrottleinputfromthetrans-
mitter.Assuch,thethrottlecurvesettingonthetransmitterisrequired.
Note:whentheRev.Lmtmodeisselected,thismodeshouldalsobeselected.
Setting:GOVERNOR/Rev.LmtInitialsetting:GOVERNOR
(4) Yaw. Comp: Governor working mode
Yawcompensationallowsthegovernortomorerapidlycorrectforchang-
esinpowerdemandsofthemodelresultingfromyawinput.Setthemode
tomatchthegyroinstallationdirection.Selectfrom:CW/TOP,CW/BOTM,
CCW/TOP,CCW/BOTM.
Note:iftheuserhasselectedthegovernoronlymode,thisparameteris
inhibited.
Revolutionfluctuationinthecaseofpirouettes
Thegovernordetectstherpmviatherevolutionsensormountedinthe
enginesection.Duringapirouettes,thehelicopteritselfrotates,so that
itspirouettesspeedisadded(reduced)totheenginespeed.Therefore,
themainrotorspeedwillfluctuateaccordingly.SincetheCGYhasagyro,
itcanaccuratelymeasurethepirouettespeed.Theyawratecorrectionis
thusdeterminedbyacombinationofgyrofunctionandgovernorfunction.
CW:clockwiserotordirection
CCW:counterclockwiserotordirection
TOP:Gyrotop/nameemblemfacingup
BOTM:Gyrotop/nameemblemfacingdown
Setting:CW/TOP,CW/BOTM,CCW/TOP,CCW/BOTMInitialsetting:CW/TOP

Related product manuals