Garmin ECHOMAP UHD Series - User Manual

ECHOMAP
™
UHD
INSTALLATION
INSTRUCTIONS
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
To obtain the best performance and to avoid damage to your
boat, install the device according to these instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin
®
Product Support.
Tools Needed
• Drill
• Drill bits
◦ Bail mount: drill bits appropriate for the surface and
hardware
◦ Swivel mount: 3 mm (
1
/
8
in.) drill bit
◦ Flush mount: 3 mm (
1
/
8
in.) and 9.5 mm (
3
/
8
in.) drill bits
• #2 Phillips screwdriver
• Jigsaw or rotary tool
• File and sandpaper
• Marine sealant (optional)
Mounting Considerations
You can mount the device using one of three methods.
Bail mount: You can mount the device using the bail mount,
which allows you to tilt the device.
Swivel mount: You can mount the device using the swivel base
and bail mount, which allows you to swivel and tilt the device.
Not available on the ECHOMAP UHD 9x models.
Flush mount: You can mount the device in the dashboard,
which provides a more integrated installation.
Before permanently installing any part of your device, you
should plan the installation by determining the location of the
various components.
• The mounting location must provide a clear view of the
screen and access to the keys on the device.
• The mounting location must be sturdy enough to support the
device and the mount.
• The cables must be long enough to connect the components
to each other and to power.
• To avoid interference with a magnetic compass, do not install
the device closer to a compass than the compass-safe
distance value listed in the product specifications.
Fixed-Bail Mounting the Device
NOTICE
If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid cracking in the gel-coat layer when the screws are
tightened.
1
Select the mounting hardware appropriate for your mounting
surface and for the bail-mount bracket.
2
Using the bail-mount bracket as a template, mark the pilot
holes through the screw holes.
3
Using a drill bit appropriate for the mounting hardware, drill
the four pilot holes.
4
Using the selected mounting hardware, secure the bail-mount
bracket to the mounting surface.
5
Install the bail-mount knobs on the sides of the cradle.
6
Place the cradle into the bail-mount bracket , and tighten
the bail-mount knobs.
7
Connect each cable to a port on the cradle, using the locking
bracket or locking rings to secure the cables to the cradle
(Connection Considerations, page 2).
TRA
REGISTERED No:
ER59438/17
DEALER No:
DA0015955/08
November 2019
190-02598-91_0A

Summary

Important Safety Information

Safety Warnings and Precautions

Safety warnings and precautions regarding the inline fuse and protective gear for installation.

Installation Guidance

General advice on reading instructions, planning location, and contacting support.

Mounting the Device

Mounting Considerations

Plan location for clear view, sturdy support, and cable access.

Fixed-Bail Mounting

Steps for securing the device using the fixed bail mount bracket.

Bail Mounting with Swivel Base

Mount the device using the swivel base and bail mount for adjustable viewing.

Flush Mounting

Instructions for a more integrated installation by flush mounting in the dashboard.

Connecting Components

Connection Considerations

Secure cables to the cradle using locking brackets or rings.

Connecting Cables to ECHOMAP Cradle

Connect cables to correct ports on the cradle using locking rings.

Power and Data Cable Usage

Details on the wiring harness for power and NMEA 0183 device connections.

Connecting to Power Source

Connect the red power wire to ignition/switch, black to ground.

Transducer and Data Sharing

Connect transducer cable and share data with other Garmin devices.

NMEA 2000 and Ferrite Beads

NMEA 2000 setup and installing ferrite beads for noise reduction.

Device Installation and Specifications

Installing Device in Cradle

Securely place the device into the cradle until it fastens with an audible click.

Removing Device from Cradle

Steps to release and remove the device from its cradle using the release lever.

Product Specifications

Technical details including material, water rating, dimensions, and power draw.

NMEA 2000 PGN Details

List of PGNs for NMEA 2000 transmit and receive functions.

NMEA 0183 Sentence Data

Details on NMEA 0183 sentences for data transmission and reception.

Garmin ECHOMAP UHD Series Specifications

General

Brand	Garmin
Model	ECHOMAP UHD Series
Category	Racks & Stands
Language	English