7
OPERATING INSTRUCTIONS
Operating Instructions
- Press the "MODE" button until the "COOL"
indicator light comes on.
- Press the ADJUST buttons "+" or " - " to
select your desired room temperature. The
temperature can be set within a range of
O O O O
17 C-30 C/62 F-88 F.
- Press the "FAN SPEED" button to choose the
fan speed.
- Press the "MODE" button until the "DRY"
indicator light comes on.
- Under this mode, you cannot select a fan
speed or adjust the temperature. The fan
motor operates at LOW speed.
- Keep windows and doors closed for the
best dehumidifying effect.
- Do not put the duct to window.
COOL operation
- Press the "MODE" button until the
"FAN " indicator light comes on.
- Press the "FAN SPEED" button to
choose the fan speed. The temperature
cannot be adjusted.
- Do not put the duct to window.
FAN operation
TIMER operation
- Press the "MODE" button until the "HEAT"
indicator light comes on.
- Press the ADJUST buttons "+" or " - " to
select your desired room temperature. The
temperature can be set within a range of
O O O O
17 C-30 C/62 F-88 F.
- Press the "FAN SPEED" button to choose the
fan speed. For some models, the fan speed
cannot be adjusted under HEAT mode.
HEAT operation
(cool-only models without heating operation)
AUTO operation
- When you set the air conditioner in AUTO
mode, it will automatically select cooling,
heating (cooling only models without heating
operation), or fan-only operation depending
on what temperature you have selected and
the room temperature.
- The air conditioner will control room
temperature automatically based on the
temperature point set by you.
- Under AUTO mode, you cannot
select the fan speed.
9
FOLLOW ME/TEMP SENSING feature (optional)
To activate the Follow Me/Temp Sensing
feature, point the remote control toward
the unit and press the Follow Me/Temp
Sensing button. The remote displays the
actual temperature at its location. The
remote control will send this signal to the
air conditioner every 3 minutes until
the Follow Me/Temp Sensing button is
pressed again. If the unit does not receive
the Follow Me/Temp Sensing signal during
any 7-minute interval, the unit will beep to
indicate the Follow Me/Temp Sensing mode
has ended.
NOTE:This feature can be activated from the
remote control ONLY. The remote control
serves as a remote thermostat that allows for the
precise temperature control at
its location.
- When the unit is on, press the
Timer button to initiate the Auto-off
stop program. The TIMER OFF
indicator light illuminates. Press the
UP or DOWN button to select the desired
time. Press the TIMER button again
within 5 seconds, to initiate the Auto
-on start program. The TIMER ON
indicator light illuminates. Press
the UP or DOWN button to select the
desired Auto-on start time.
- When the unit is off, press the Timer
button to initiate the Auto-on start
program. Press it again within 5
seconds to initiate the Auto-off stop
program.
- Press or hold the UP or DOWN
button to change the Auto time by
half-hour increments up to 10 hours,
then at 1-hour i
ncrements up to 24
hours. The control will count down
the time remaining until start.
- The system will automatically revert
back to displaying the previous temper-
ature setting if there is no operation
in a 5-second period.
Error codes and protection code:
E1- Room temperature sensor error-
Unplug the unit and plug it back in.
If error repeats, call for service.
E2- Evaporator temperature sensor error-
Unplug the unit and plug it back in.
If error repeats, call for service.
E3- Condenser temperature sensor error-
Unplug the unit and plug it back in. If error
repeats, call for service (on some models).
E4- Display panel communication error-
Unplug the unit and plug it back in.
I
f error repeats, call for service.
P1- Bottom tray is full - Connect the
drain hose and drain the collected
water. If protection repeats, call
for service.
To Next Page
Loading...
