How to fix curling laminated items from GBC 640T?
If your laminated items are curling when using the GBC Laminator, it may be due to unequal tension between the top and bottom film rolls. Another possible cause is that the speed setting is too slow; slightly increase the laminator speed.
What to do if the rollers on my GBC 640T do not turn?
If the rollers on your GBC Laminator aren't turning, check for these potential issues: * Infrared eyes might be blocked; unblock them. * The feed tray interlock latch might not be correctly in place; slide the interlock latch all the way to the left into the side frame.
Why is my GBC Laminator not sealing properly?
There are several reasons why your GBC Laminator might not be providing satisfactory adhesion. It could be due to insufficient roller pressure, which requires adjustment. The laminate may be improperly loaded. The rollers may need cleaning. Alternatively, the item being laminated might be unsuitable for adhesion, perhaps because it's dirty or has a non-porous surface.
What to do if adhesive is deposited on the rollers of my GBC 640T?
If you notice adhesive on the rollers of your GBC Laminator, it could be because the top and bottom film webs are not aligned. Another cause could be that the laminate was improperly loaded.
Why doesn't the LCD light up on my GBC 640T?
If the LCD on your GBC Laminator isn't illuminating, first ensure the laminator is properly connected to an electrical supply by inserting the attachment plug into the receptacle. Also, check if the circuit breaker has tripped and reset it if necessary.
General| Maximum Film Thickness | 10 mil |
|---|---|
| Power Consumption | 650W |
| Weight | 7.7 lbs |
| Maximum Pouch Thickness | 10 mil |
| Number of Rollers | 2 |
| Carrierless lamination | Yes |
| Type | Pouch Laminator |
| Maximum Width | 640 mm |
| Speed | 1.2 m/min |
| Throat Width | 640 mm |
| Laminating Speed | 1.2 m/min |
| Maximum Document Width | 640 mm |
| Power Requirements | 120V, 60Hz |
General safety precautions and warnings for laminator operation.
Guidelines for safe electrical connection and usage.
Details the terms and conditions of the product's warranty.
Technical details including dimensions, electrical requirements, and speed.
Notices regarding FCC and Canadian regulatory compliance.
Information on the impact of unauthorized device modifications.
Steps to take before installing the laminator, including package inspection.
Step-by-step guide for correctly setting up the laminator.
Identification of film shafts and the release liner take-up mechanism.
Description of idler bars, unwind, and rewind shafts.
Overview of main rollers and the function of the safety sensor.
Explanation of emergency stop button and feed table features.
Details on the control panel and print clamp mechanism.
Guide to using tension adjustment knobs for film control.
Instructions for adjusting roller pressure for different applications.
Explanation of media core adapters for holding film rolls.
Identification of components related to the rewinder system.
Description of the power switch, circuit breaker, and nomenclature plate.
Details about the power cord and the foot switch operation.
Overview of the control panel display and its functional buttons.
Explanation of temperature settings and controls.
Explanation of speed settings and controls.
Basic steps to operate the laminator.
Instructions for loading different types of laminating film.
Steps to remove and install the print clamp.
Steps to remove and install the feed table.
Detailed process for mounting film rolls onto the supply shafts.
Procedure for threading film using a threading card.
Method for loading new film by tacking it to existing film.
Instructions for decaling items in two separate passes.
Guidelines for mounting items using the laminator.
Advice for threading pressure-sensitive adhesive film.
Instructions for pre-coating mounting boards with film.
Process for mounting items without decaling.
Procedure for roll-to-roll lamination.
Techniques for aligning film and adjusting tension for optimal results.
Procedures for testing the film web and clearing jams.
General guidelines and tips for successful lamination.
General advice on maintaining the laminator's condition.
Step-by-step instructions for cleaning the machine's rollers.
Solutions for common problems encountered during operation.
General notes and reminders related to the manual.
To Next Page
