GE D60 - Page 433

826 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

GE Multilin D60 Line Distance Protection System 5-299

5 SETTINGS 5.7 CONTROL ELEMENTS

5

Figure 5–153: ARCING CURRENT MEASUREMENT

Initiate

Breaker

Contacts

Part

Arc

Extinguished

100 ms

Programmable

Start Delay

Start

Integration

Stop

Integration

Total Area =

Breaker

Arcing

Current

(kA·cycle)

Table of Contents

Default Chapter3
- Table of Contents3
1 Getting Started11
- Important Procedures11
  - Cautions and Warnings11
  - Inspection Procedure12
- Ur Overview13
- Enervista Ur Setup Software15
- Ur Hardware27
- Using the Relay28
2 Product Description31
- Introduction31
- Order Codes38
- Specifications47
3 Hardware63
- Description63
  - Panel Cutout63
  - Rear Terminal Layout69
- Wiring70
- Direct Input and Output Communications86
4 Human Interfaces103
- Enervista Ur Setup Software Interface103
- Extended Enervista Ur Setup Features107
- Faceplate Interface116
5 Settings131
- Overview135
- Product Setup142
- System Setup233
- Flexlogic276
- Grouped Elements301
- Control Elements389
- Inputs and Outputs480
- Transducer Inputs and Outputs497
- Testing 5.10.1 Test Mode505
6 Actual Values510
- Overview510
  - Actual Values Menu510
- Status512
- Records534
- Product Information537
  - Model Information537
  - Firmware Revisions537
7 Commands and539
- Commands539
- Targets544
8 Theory of Operation551
- Distance Elements551
- Phase Distance Applied to Power Transformers Description561
  - Example564
- Ground Directional Overcurrent566
  - Description566
  - Example566
- Series Compensated Lines568
  - Description568
- Single-Pole Tripping571
- Fault Locator588
9 Application of589
- Application Guidelines589
Settings589
- Introduction589
- Impact of Memory Polarization589
- High-Set Overcurrent Elements589
- Distance Elements (Stepped Distance Scheme)590
  - Phase Distance590
  - Ground Distance591
- Protection Signaling Schemes594
- Series Compensated Lines599
- Phase Distance through Power Transformers602
  - Example602
10 Maintenance603
- Modules603
  - Replace a Module603
- Batteries605
  - Replace Battery605
  - Dispose of Battery607
Parameter Lists611
- Flexanalog Items611
- A.1.1 Flexanalog Items611
- Flexinteger Items621
- A.1.2 Flexinteger Items621
Modbus Rtu Protocol623
- Introduction623
- Physical Layer623
- Data Link Layer623
- B.1.1 Introduction623
- Modbus Rtu Crc-16 Algorithm624
Modbus Function Codes626
- Supported Function Codes626
- Read Actual Values or Settings (Function Code 03/04H626
- Execute Operation (Function Code 05H627
- Store Single Setting (Function Code 06H627
- Store Multiple Settings (Function Code 10H628
- Exception Responses628
- B.3.1 Obtaining Relay Files Via Modbus629
File Transfers630
Memory Mapping631
- Modbus Memory Map631
- Data Formats708
- B.4.2 Data Formats708
Iec 61850747
Overview747
- Introduction747
- Communication Profiles747
- C.1.1 Introduction747
Server Data Organization748
- Overview748
- Ggio1: Digital Status Values748
- Ggio2: Digital Control Values748
- Ggio3: Digital Status and Analog Values from Goose Data748
- Ggio4: Generic Analog Measured Values748
- C.2.1 Overview748
- Mmxu: Analog Measured Values749
- Protection and Other Logical Nodes749
Server Features and Configuration751
- Buffered/Unbuffered Reporting751
- File Transfer751
- Timestamps and Scanning751
- Logical Device Name751
- Location751
- Logical Node Name Prefixes752
- Connection Timing752
- Non-Iec 61850 Data752
- Communication Software Utilities752
Generic Substation Event Services: Gsse and Goose753
- Overview753
- Gsse Configuration753
- Fixed Goose753
- Configurable Goose753
- C.4.1 Overview753
- Ethernet Mac Address for Gsse/Goose756
- Gsse ID and Goose ID Settings756
Iec 61850 Implementation Via Enervista Ur Setup757
- Overview757
- C.5.1 Overview757
- Configuring Iec 61850 Settings758
- About ICD Files759
- Creating an ICD File with Enervista Ur Setup763
- About Scd Files763
- Importing an Scd File with Enervista Ur Setup766
Acsi Conformance768
- Acsi Basic Conformance Statement768
- Acsi Models Conformance Statement768
- Acsi Services Conformance Statement769
Logical Nodes Table772
- C.7.1 Logical Nodes Table772
Iec 60870-5-103777
- Overview777
- Factor and Offset Calculation to Transmit Measurand777
- D.1.1 Overview777
- Interoperability Document778
- D.1.3 Interoperability Document778
Iec 60870-5-104 Protocol783
- Interoperability Document783
- E.1.1 Interoperability Document783
- Points List791
- E.1.2 Points List791
Device Profile Document793
- Dnp V3.00 Device Profile793
- F.1.2 Implementation Table796
Dnp Point Lists800
- Binary Input Points800
- Binary and Control Relay Output801
- Counters802
- F.2.3 Counters802
- Analog Inputs803
- F.2.4 Analog Inputs803
Radius Server Configuration805
Change Notes807
- Revision History807
- H.1.1 Revision History807
- Changes to the D60 Manual808
Abbreviations812
- Standard Abbreviations812
  - H.2.1 Standard Abbreviations812
  - H.3.1 Ge Multilin Warranty814

Related product manuals

Preview: GE 869

Preview: GE 850

Preview: GE F35

Preview: GE 339

Preview: GE F60

Preview: GE 889

Preview: GE G60

Preview: GE 350

Preview: GE 845

Preview: GE MI-869

Preview: GE Multilin 850

GE Multilin 850

Preview: GE Multilin g60

GE Multilin g60