GE DCVH680EJ1WW - User Manual

Installation
Instructions
Electric Drger
09
Questions or Installation? Call: 1-800-GECARES (US)
or Visit our Web site at: www.GEApplionces.com (US)
PEDESTALS FOR DRYERS
(comes with individual installation instructions)
Three models available: - SBSD227F
- SBSDIO7H - SBSD137H
BEFOREYOU BEGIN
Read these instructions completelg and carefullg.
•IMPORTANT-savetheseinstructionsforlocal
inspector's use.
• IMPORTANT- Observea,governing codesand
ordinances.
• Note to Installer - Besure to leave these instructions with
the customer.
• Note to Customer- Keepthese instructions with your Use
and Care Book for future reference.
• Before the old dryer is removed from service or discarded,
remove the dryer door.
• Service information and the wiring diagram are located in
the control console.
• Do not allow children on or in the appliance. Close super-
vision of children is necessary when the appliance is used
near children.
• Install the dryer where the temperature is above 50°F for
satisfactory operation of the dryer control system.
WA ! G- RISKOFFIRE
• To reduce the risk of severe injury or death, follow all installation instructions.
• Clothes dryer installation must be performed by a qualified installer.
• Install the clothes dryer according to these instructions and in accordance
with local codes.
• This dryer must be exhausted to the outdoors.
• Use only 4" rigid metal ducting for exhausting the clothes dryer to the
outdoors.
• DO NOTinstall a clothes dryer with flexible plastic ducting materials.
If flexible metal (semi-rigid or foil-type) duct is installed, it must be UL listed
and installed in accordance with the instructions found in "Connecting The
Dryer To House Vent" on page S of this manual. Flexible venting materials
are known to collapse, be easily crushed, and trap lint. These conditions will
obstruct dryer airflow and increase the risk of fire.
• Do not install or store this appliance in any location where it could be
exposed to water and or weather.
• Save these instructions. (Installers: Besure to leave these instructions with
the customer).
NOTE: Installation and service of this drger
requires basic mechanical and electrical skills.
It is your responsibilitg to contact a qualified
installer to make the electrical connections.
TOOLS YOU
WILL NEED
SLIPJOINT PLIERS
FLAT BLADESCREWDRIVER
PHILLIPSSCREWDRIVER
4" DIA METALDUCT
(RECOMMENDED)
)
4" DIA FLEXIBLEMETAL(SEMI-RIGID)
ULLISTEDTRANSITIONDUCT
(IFNEEDED)
KITWXOSX10077(INCLUDES2 ELBOWS)
4"DIA FLEXIBLEMETAL(FOILTYPE)
ULLISTEDTRANSITIONDUCT
(IFNEEDED.)
MATERIALS YOU WILL NEED
/4"DUCT
CLAMPS(2)
OR
/4"SPRING
CLAMPS(2)
%
4"DIA,METAL
ELBOW
DUCTTAPE
EXHAUST SAFETY
HOOD GLASSES
GLOVES
3/4" STRAIN
RELIEF
ULRECOGNIZED
DRYERPOWERCORD
KIT(NOTPROVIDED
WITH DRYER)
ULRATED
120/240V,30A
WITH 3 OR4 PRONGS.
IDENTIFYTHEPLUG
TYPEASPERTHE
HOUSERECEPTACLE
BEFOREPURCHASING
LINECORD.
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Prepare the Area and Exhaust for Installation of New
Dryer (see section 1).
Check and Ensure the Existing External Exhaust is
Clean (see section 1) and Meets Attached Installation
Specifications (see section 3).
Remove the Foam Shipping Pads (see section 1).
Move the Dryer to the Desired Location.
Connect the Power Supply (see section 2).
Connect the External Exhaust (see section 4).
Level Your Dryer (see section 5).
Step 8
Step 9
Check the Operation of the Power Supply and
Venting.
Place the Owners Manual and the Installation
Instructions in a Location Where They Will Be
Noticed By the Owner.
For Alcove or Closet Installation, see section 6.
For Bathroom or Bedroom Installation, see section 7.
For Mobile or Manufactured Home see, section 8.
For side or bottom exhaust, see section 9.
500A436PO09 RevO Pub # 31-16228

GE DCVH680EJ1WW Specifications

General

Brand	GE
Model Number	DCVH680EJ1WW
Type	Electric
Color	White
Control Type	Electronic
Temperature Settings	4
Wrinkle Care Option	Yes
End of Cycle Signal	Yes
Drum Light	Yes
Voltage	240 V
Amperage	30 A
Energy Star Certified	No
Weight	125 lbs
Width	27 in

Summary

Electrical Connection Information

Electrical Requirements

Details the necessary circuit type, voltage, and amp service required for the dryer. Ensures proper power supply.

Grounding Instructions

Explains the requirement for grounding the dryer to a metal wiring system or using an equipment-grounding conductor.

Connecting Dryer Using 4-Wire Connection

Guides the 4-wire electrical connection, which is mandatory for mobile home installations.

Connecting the Dryer to House Vent

Rigid Metal Transition Duct

Recommends rigid metal duct for best drying performance and reduced risk of crushing and kinking.

UL-Listed Flexible Metal (Semi-Rigid) Transition Duct

Covers the use of semi-rigid flexible metal duct, its limitations, and installation requirements.

UL-Listed Flexible Metal (Foil-Type) Transition Duct

Details the use of foil-type flexible duct in specific situations and its restrictions.

Exhaust Connection

Standard Rear Exhaust (Vented at floor level)

Instructions for connecting the dryer exhaust to the external hood at floor level.

Standard Rear Exhaust (Vented above floor level)

Instructions for rear exhaust venting when the outlet is above floor level.

Leveling and Stabilizing Your Dryer

How to adjust the leveling legs to ensure the dryer is stable and level.

Installation Locations and Venting

Alcove or Closet Installation

Details clearances and requirements for installing the dryer in an alcove or closet.

Bathroom or Bedroom Installation

Covers installation in bathrooms or bedrooms, emphasizing venting compliance.

Mobile or Manufactured Home Installation

Outlines installation standards and requirements specific to mobile and manufactured homes.

Dryer Exhaust to Right, Left or Bottom Cabinet

Adding New Duct

Instructions for modifying the dryer cabinet to add a new duct for side or bottom exhaust.

Adding Elbow and Duct for Exhaust to Left or Right Side of Cabinet

Steps for adding an elbow and duct for side exhaust connections.

Reversing the Door Swing

Before You Start

Initial steps and warnings before attempting to reverse the door swing.

Remove Door Assembly

Detailed steps for safely removing the dryer door from the appliance.

Remove Hinge

Instructions on how to detach the hinge assembly from the door.

Reinstall Hinge Assembly

Steps for attaching the hinge assembly to the opposite side of the door.

Reinstall Nuts and Hinge Cover

Reassembling the nuts and hinge cover after moving the hinge.

Reassemble Door Assembly

Putting the door components back together and securing them.

Reinstall Door Assembly

Final steps to attach the reversed door back onto the dryer.

Move Strike Bracket

Instructions to relocate the door strike bracket for the reversed door.