nstallati
nst cti
lectric
Drye
Questions on Installation? Call" 1-800-GECARES (US)
or Visit our Web site at: www.GEAppliances.com (US)
BEFOREYOU BEGIN
Read these instructions completely and
carefully.
IMFORTANT- S.,,ethese
e
instructions fbr local inspector's use.
"IMPORTANT- Obse,,,e
all governingcodes and ordinances°
* Note to Installer- Be sure to leave these
instructions with the custotner.
* Note to Customer - Keep these instruc>
ions with your Use and Care Book for
furore reference.
* Before the old dryer is removed flom
service or discarded, remove the d_Ter
door.
* Service infbrmation and the wiring dia-
gram are located in the control console.
* Do not allow children on or in the appli-
ance. Close supe_wision of children is
necessa_ T when the appliance is used
near children.
* Install the (bTer where the temperature
is above 50°F for satisfilctory operation of
the d_Ter control system.
kWARN I N G RIsKOF
* To reduce the risk of severe i_i m T or death, fbllow all installation instruc-
tions.
* Clothes d_Ter insmlla6on must be performed by a qualified installer.
* Install the clothes d_Ter according to these instructions and in accordance
with local codes.
* This d_Ter must be exhausted to the outdoors.
* Use only 4" rigid metal duc6ng for exbaus6ng the clothes d_Ter to the
outdoors.
* DO NOT install a clothes d,Ter with flexible plastic ducdng materials. If
flexible metal (semi-rigid or fbil-type) duct is installed, it must be UL listed
and installed in accordance with the instructions found in "Connecting The
D,Ter To House Vent" on page 5 of this manual. Flexible venting materials
are known to collapse, be easily crushed, and trap lint. These conditions will
obstruct dryer airflow and increase the risk of fire.
* Do not install or store this appliance in any location where it coukt be
exposed to water and or weather.
* Save these instructions. (Installers: Be sure to leave these instructions with
the customer).
NOTE: installation and service of this dryer requires basic
mechanical and electrical skills, it is your responsibility to
contact a qualified installer to make the electrical connections.
TOOLS YOU
WiLL NEED
SLIPJOINTPLIERS
FLATBLADESCREWDRIVER
PHILLIPSSCREWDRIVER
%
MATERIALS YOU
)
4" DIA.METALDUCT
(RECOMMENDED)
4"DIA,FLEXIBLEMETALSEMI-RIGID)
ULLSTEDTRANSTONDUCT
(IFNEEDED)
KITWXO8X10077(INCLUDES2 ELBOWS)
4"DUCT
CLAMPS(2)
OR
4"SPRING
CLAMPS(2)
%
4"DIA.METAL
ELBOW
4"DIA.FLEXIBLEMETALFOILTYPE)
ULLSTEDTRANSTONDUCT
(IFNEEDED.)
DUCTTAPE
WiLL NEED
EXHAUST SAFETY
HOOD GLASSES
3/4"STRAIN
GLOVES RELIEF
ULRECOGNIZED
DRYERPOWER
CORDKIT
(NOTPROVIDED
WITHDRYER)
ULRATED
120/240V,30A
WITH3OR4 PRONGS.
IDENTIFYTHEPLUG
TYPEASPERTHE
HOUSERECEPTACLE
BEFOREPURCHASING
LINECORD.
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Prepare the Area and Exhaust for Installation of
New Dryer (see section 1).
Check and Ensure the Existing External Exhaust is
Clean (see sec6on 1) and Meets Attached Installa6on
Specifications (see sec6on 3).
Remove the Foam Shipping Pads (see sec6on 1).
Move the DtTer to the Desired Location.
Connect the Power Supply (see secdon 2).
Connect the External Exhaust (see secdon 4).
Level Your D_Ter (see sec6on 5).
Step 8
Step 9
Check the Operation of the Power Supply
an d Ve n tin g.
Place the Owners Manual and the Installation
Instructions in a Locadon Where They Will Be
Noticed By the Owner.
For Alcove or Closet Installation, see section 6.
For Bathroom or Bedroom Installation, see section 7.
For Mobile or Manufi_cmred Home see, section S.
For side or bottom exhaust, see section 9.
To Next Page
Need help?
General
