How to turn off the beeping at the end of the cycle on my GE Dishwasher?
To turn off the double beep indicator (or re-activate it if it was previously turned off), press the Heated Dry pad 5 times within 3 seconds. A triple beep will sound to indicate the end-of-cycle beep option has been turned on or off.
What does it mean when the start status indicator light is flashing on my GE GBT 632 Dishwasher?
The flashing start status indicator light means the door was opened or the cycle was interrupted. Press the Start pad once and close the door within 4 seconds to start the dishwasher.
Why are there black or gray marks on my dishes from my GE Dishwasher?
Black or gray marks on dishes are usually caused by aluminum utensils rubbing against them. Remove the marks with a mild, abrasive cleaner.
Why does my GE GBT 632 have long cycle times?
Longer cycles are normal because the dishwasher washes by alternating mid and lower spray arms. Also, the turbidity sensor senses how much soil is on the dishes. Heavily soiled dish loads will add more time to the cycle. Allow the cycle to complete for the best wash and dry performance.
How to get rid of cloudiness on glassware in my GE Dishwasher?
Cloudiness on glassware can be due to: * A combination of soft water and too much detergent: Use less detergent if you have soft water and wash glassware in the shortest cycle. * Low performing phosphate-free detergent: See A white film on glassware, dishware and the interior in this TROUBLESHOOTING TIPS section. * Water temperature entering the dishwasher exceeds 150°F (66°C): Lower the water heater temperature.
How to fix spots and filming on glasses and flatware in GE GBT 632?
Spots and filming can occur due to several reasons: * Extremely hard water: Use rinse agents like Finish® Jet-Dry® Rinse Aid. A softener may be required if the water is extremely hard. * Low inlet water temperature: Ensure the water temperature is at least 120°F (49°C). * Overloading or improper loading: Load the dishwasher as shown in the Loading section. * Old or damp powder detergent: Use fresh, highly rated detergent such as Finish® Quantum® Automatic Dishwashing Detergent. * Empty rinse agent dispenser: Refill the dispenser with a rinse agent such as Finish® Jet-Dry® Rinse Aid. * Too little or low performing detergent: Use the proper amount of highly rated detergent.
What to do if my GE GBT 632 Dishwasher won’t run?
If your dishwasher isn't running, check these possible causes: * A fuse may be blown or the circuit breaker tripped: Replace the fuse or reset the circuit breaker. Try removing other appliances from the circuit. * The power may be turned off: Ensure the wall switch (often located next to the disposer switch) is turned on. * The control panel may be locked: Unlock the control panel. See the Getting started section.
Why does my GE Dishwasher control panel respond but the dishwasher never fills with water?
If your GE dishwasher's control panel responds to inputs but the dishwasher never fills with water: * Make sure the door is firmly closed. * Ensure the water valve (usually under the sink) is turned on. * The flood float may be stuck. Remove the ultra-fine filter and lightly tap the piece under it that looks like a salt shaker, then replace the filter.
What to do if water won’t pump out of the tub of my GE GBT 632?
If water won't pump out of your GE dishwasher tub, the drain may be clogged. If you have an air gap, clean it. If the dishwasher drains into a disposer, run the disposer to clear it. Check if your kitchen sink is draining well; if not, you may need a plumber.
Why don't my dishes dry in my GE GBT 632 Dishwasher?
Several factors can affect drying performance in your GE dishwasher: * Ensure the inlet water temperature is at least 120°F. Select Heated Dry or Dry Boost, and use Wash Temp Boost. * Check the rinse agent dispenser and fill as required. * Leave the door closed after the clean light appears to allow the fan to run for an additional 20 minutes on some models. Note that opening the door will cancel this fan extension. * If using the Light cycle, switch to a different cycle, as it uses lower water temperatures. * Allow cycles to fully complete.
General| Brand | GE |
|---|---|
| Model | GBT 632 Series |
| Category | Dishwasher |
| Language | English |
Guidelines for installing and maintaining the dishwasher correctly to ensure safety.
Basic precautions to follow while operating the dishwasher to prevent injury or damage.
Important safety information related to hydrogen gas in water heaters.
Safety measures to prevent children from becoming trapped in the dishwasher.
Specifications and precautions for the dishwasher's electrical connections.
To Next Page
