GE GDP670 User Manual (English)

Questions and Answers:

M
meganpierceAug 22, 2025
Why are my dishes and flatware not clean in my GE GDP670?
- M
  Matthew MitchellAug 22, 2025
  There are several reasons why your dishes and flatware might not be clean. The Ultra-Fine Filter or Fine Filter could be clogged. The inlet water temperature might be too low. The water pressure could be temporarily low. The air gap or disposer might be clogged. The high drain loop or air gap might not be installed correctly. You might be improperly loading the rack, or you might be using a poor-performing detergent. Make sure that large dishware does not block the detergent dispenser or the wash arms. Normal water pressure to the dishwasher should be 20-120 psi. Use high quality detergents such as Cascade® Platinum™ ActionPacs™ or Finish® Quantum® Automatic Dishwashing Detergent.
A
Amanda VillaAug 23, 2025
What does it mean when my GE GDP670 Dishwasher BEEPS once every minute?
- J
  Jessica ElliottAug 23, 2025
  If your dishwasher beeps once every minute, this is a reminder that the dishwasher door has been left open during operation. It will continue beeping until you press Start and close the door. Press Start and close the door.
B
Brenda MooreAug 25, 2025
Why is my GE Dishwasher control panel responding to inputs but never filling with water?
- W
  Walter FullerAug 25, 2025
  If the control panel responds but the dishwasher doesn't fill, make sure the door is firmly closed. Also, ensure the water valve (usually under the sink) is turned on. Finally, the flood float may be stuck; remove the Ultra-Fine filter and lightly tap the piece under the ultra fine filter that looks like a salt shaker, then replace the filter.
A
amy12Aug 26, 2025
Why are my dishes not drying in my GE GDP670 Dishwasher?
- M
  Michael JohnsonAug 27, 2025
  Dishes not drying can be due to low inlet water temperature. Make sure inlet water temperature is at least 120°F. Select Boost Dry. Use Boost option. Select a higher cycle, such as Steam-Sani, Presoak- Sani, or Sanitize. Also, the rinse agent dispenser might be empty; check and fill as required. Additional drying time may be needed; leave the door closed after the Clean light appears to allow the fan to run an additional 90 minutes. Note: If you open the door, this fan extension will be cancelled.
W
Whitney RivasAug 27, 2025
Why is my GE GDP670 Dishwasher beeping at the end of the cycle?
- G
  gbutlerAug 27, 2025
  The dishwasher beeps twice at the end of the cycle. To turn off the double beep indicator (or re-activate it if it was previously turned off), press the Dry Boost pad 5 times within 3 seconds. A triple beep will sound to indicate the end-of-cycle beep option has been turned on or off.
A
Andre FrancoAug 30, 2025
How to fix cloudiness on glassware in my GE GDP670?
- J
  Joshua RobinsonAug 30, 2025
  Cloudiness on glassware can be caused by a combination of soft water and too much detergent. This is called etching and is permanent. To prevent this, use less detergent if you have soft water and wash glassware in the shortest cycle that will get it clean. It can also be caused by low performing phosphate-free detergent, see A white film on glassware, dishware and the interior in this TROUBLESHOOTING section, or water temperature entering the dishwasher exceeding 150°F, which could also be etching, so lower the water heater temperature.
P
Peter BradleyAug 31, 2025
What does it mean when the start status indicator light is flashing on my GE GDP670 Dishwasher?
- S
  Sergio HowardSep 1, 2025
  A flashing start status indicator light means the door was opened or the cycle was interrupted. To resolve this, press the Start pad once and close the door within 4 seconds to start the dishwasher. Press the Start pad a second time when the dishwasher is running only if you wish to cancel the cycle.
L
Louis LewisSep 2, 2025
How to fix a white film on glassware, dishware, and the interior of my GE GDP670?
- W
  williamsmithSep 2, 2025
  A white film is likely caused by a low-quality phosphate-free dishwasher detergent. To remove it, run a cycle with citric acid (WD35X151 kit found online) or use high-quality rinse agents like Cascade® Platinum™ Dishwasher Cleaner or Finish® Dishwasher Cleaner. Pour citric acid into the detergent cup, load filmed items (excluding silverware), and run a complete cycle without detergent. Alternatively, use a vinegar rinse: pour 1 cup of vinegar into the dishwasher just after the detergent cup opens and complete the cycle. Repeat as needed. Use high quality detergents such as Cascade® Platinum™ ActionPacs™ or Finish® Quantum® Automatic Dishwashing Detergent to help prevent film build-up.
A
Anita AllenSep 3, 2025
Why is there water standing in the bottom of my GE GDP670 Dishwasher tub?
- W
  webbmariaSep 3, 2025
  If there's water standing in the bottom of the tub, the air gap might be clogged. Clean the air gap. Also, check if the high drain loop or air gap is not installed; refer to the Installation Instructions for proper drain line installation.
J
Justin PotterSep 4, 2025
Why won’t water pump out of the tub of my GE GDP670?
- J
  Jessica CraigSep 5, 2025
  If water won’t pump out of the tub, the drain is likely clogged. If you have an air gap, clean it. If the dishwasher drains into a disposer, run the disposer to clear it. Check to see if your kitchen sink is draining well. If not, you may need a plumber.

GE GDP670 Specifications

General

Type	Built-In
Capacity	16 place settings
Wash Cycles	6
Drying System	Heated Dry
Water Filtration System	Yes
Rinse Aid Dispenser	Yes
Leveling Legs	Yes
Energy Star Certified	Yes
Soil Sensor	Yes
Third Rack	Yes
Stainless Steel Tub	Yes
Delay Start	Yes
Color	Stainless Steel
Wash Arms	3
Depth	24 inches