GE GTD72EBPN0DG User Manual

- Risk of Fire
• Clothes dryer installation must be performed by a
qualified installer.
• Install the clothes dryer according to these instructions
and local codes.
• DO NOT install a clothes dryer with flexible plastic venting
materials. If flexible metal (semi-rigid or foil-type) duct is
installed, it must be UL-listed and installed in accordance
with the instructions found in “Connecting the Dryer
to House Vent” later in this manual. Flexible venting
materials are known to collapse, be easily crushed and
trap lint. These conditions will obstruct dryer airflow and
increase the risk of fire.
• DO NOT install or store this appliance in any location
where it could be exposed to water or weather.
• To reduce the risk of severe injury or death, follow all
installation instructions.
• Save these instructions. (Installers: Be sure to leave
these instructions with the customer.)
In the Commonwealth of Massachusetts,
the following installation instructions apply:
• Installation must be performed by a qualified or
licensed contractor, plumber, or gasfitter qualified
or licensed by the State.
• If using a ball valve, it shall be a T-handle type.
• A flexible gas connector, when used, must not
exceed 4 feet.
FOR GAS DRYERS ONLY
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT – Save these instructions for local electrical
inspector’s use.
IMPORTANT – Observe all governing codes and
ordinances.
• Install the clothes dryer according to the manufacturer’s
instructions and local codes.
• Note to Installer – Be sure to leave these instructions
with the Consumer.
• Note to Consumer – Keep these instructions for future
reference.
• Clothes dryer installation must be performed by a qualified
installer.
• This dryer must be exhausted to the outdoors.
• Before the old dryer is removed from service or discarded,
remove the dryer door.
• Do not allow children on or in the appliance. Close
supervision of children is necessary when the appliance
is used near children.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
• Install the dryer where the temperature is above 50°F for
satisfactory operation of the dryer control system.
• Remove and discard existing plastic or metal foil duct
and replace with UL-listed duct.
• Service information and the wiring diagram are located
in the control console.
05-19 GEA
31-3000199
Questions? Call GE Appliances at 800.GE.CARES (800.432.2737) or visit our Web site at: GEAppliances.com
Dryers
Installation
Instructions
WARNING

GE GTD72EBPN0DG Specifications

General

Brand	GE
Model	GTD72EBPN0DG
Category	Dryer
Language	English

Summary

General Installation and Safety

Before You Begin

Read instructions completely, save for inspector, and observe all governing codes and ordinances.

Risk of Fire Warnings

Details hazards like fire risk from improper installation, venting materials, and installation errors.

Massachusetts Gas Dryer Requirements

Specific installation instructions and requirements for gas dryers within the Commonwealth of Massachusetts.

Dryer Dimensions and Accessories

Unpacking Your Dryer

Instructions for removing shipping pads and literature before installation.

Rough-In Dimensions

Critical clearance and sizing information for proper dryer installation.

Steam Water Hoses

Recommended hoses for steam dryer models to ensure proper operation.

Available Accessories

Lists optional parts for purchase to enhance functionality or installation.

Installation Location Requirements

Alcove or Closet Installation Clearances

Minimum clearances required for alcove or closet installations to ensure safety and airflow.

General and Mobile Home Clearances

Clearances for locations other than alcoves/closets and specific mobile home standards.

Connecting Water Inlet Hoses

Steam Dryer Water Hose Connection

Step-by-step guide for connecting water hoses to steam dryer models.

Water Supply Specifications

Required water faucet type, pressure, and softener recommendations for optimal performance.

Gas Dryer Connection - Tools and Materials

Tools for Gas Dryer Connection

Lists the necessary tools required for connecting a gas dryer.

Materials for Gas Dryer Connection

Lists the required materials for connecting a gas dryer.

Gas Dryer Supply Requirements and Connections

Gas Supply Safety & Codes

Covers gas supply safety, national codes, and connection requirements for gas dryers.

Elevation Adjustments for Gas Dryers

Guidance on adjusting gas dryer input ratings for installations at high altitudes.

Gas Dryer Supply Connection Procedure

Connecting Dryer Gas Inlet

Steps for installing elbow, adapter, and flexible connector to the dryer's gas inlet.

Gas Pressure Test Connection

How to install a tapping for checking gas inlet pressure during connection.

Gas Dryer Testing and Electrical Grounding

Testing Gas Connections for Leaks

Procedure for safely testing gas connections using soapy solution.

Gas Dryer Electrical & Grounding

Electrical connection requirements and grounding instructions for gas dryers.

Electric Dryer Connection Overview

Electric Dryer Tools, Materials & Cords

Lists tools, materials, and power cord options for electric dryer installation.

Electric Dryer Electrical & Grounding

Power Cord vs. Direct Wire Connections

Details electrical connection methods using power cords or direct wiring.

Electric Dryer Grounding Procedures

Instructions on properly grounding electric dryers for safety.

Electric Dryer Wiring Configurations

4-Wire Electric Dryer Connection

Step-by-step guide for the 4-wire connection method, essential for mobile homes.

3-Wire Electric Dryer Connection

Steps for the 3-wire connection method and its restrictions.

Dryer Exhaust Venting Requirements

Venting Safety & Material Guidelines

Crucial safety warnings and material recommendations for dryer exhaust systems.

Transition Duct Options

Explains the use of rigid and flexible metal transition ducts for venting.

Dryer Exhaust System Length & Elbows

Impact of Exhaust Length

How exhaust length affects drying performance, energy use, and lint accumulation.

Maximum Exhaust Length Chart

Chart detailing maximum allowable exhaust lengths based on turns and hood type.

Dryer Exhaust System Details

System Components & Sealing

Checklist for wall caps, joint sealing, and insulation for the exhaust system.

Rear Exhaust & Blockage Prevention

Standard rear exhaust connection and recommended configurations to prevent blockage.

Side & Bottom Dryer Venting

Side/Bottom Venting Preparation

Steps to prepare the dryer cabinet for side or bottom exhaust.

Adding Ducts for Side Venting

Instructions for connecting ducts and elbows for side exhaust configurations.

Final Dryer Setup & Venting Completion

Side/Bottom Venting Ducting Final Steps

Final duct tape application and securing for side/bottom venting.

Adding Rear Cover Plate

Instructions for installing the rear opening cover plate.

Dryer Leveling & Start-Up

Steps for leveling the dryer, plugging it in, and initial start-up.

Dryer Door Reversal - Preparation

Door Reversal Notes & Tools

Important notes, tools, and preparation for reversing dryer door swing.

Solid Door Reversal (Part 1)

Initial steps for reversing the door on solid door models.

Solid Door Reversal Completion

Solid Door Reversal (Part 2)

Continuation of steps to complete solid door reversal.

Glass Panel Door Reversal - Preparation

Glass Panel Door Reversal (Part 1)

Initial steps for reversing the door on glass panel door models.

Glass Panel Door Reversal Completion

Glass Panel Door Reversal (Part 2)

Continuation of steps to complete glass panel door reversal.