To Next PageTo Next PageHow to fix a GE Washer when the water won’t drain?
If the water isn't draining from your GE washer, check if the drain hose is kinked or improperly connected. Straighten the drain hose, ensure the washer isn't sitting on it, and verify that the top of the drain outlet is less than 8 ft (2.44 m) above the floor.
Why is the water temperature incorrect in my GE Washer?
If the water temperature in your GE Washer seems incorrect, first ensure that both hot and cold water faucets are fully turned on and that the hoses are connected to the correct faucets, noting the “H” and “C” markings on the water valves. Check the water valve screens for blockage by turning off the water source, disconnecting the hoses, cleaning the screens with a brush or toothpick, reconnecting the hoses, and turning the water back on, ensuring no leaks. Finally, verify that your house water heater is set to deliver water between 120°F and 140°F (48°C–60°C).
How to fix a GE GTW490AJ Washer that won't drain?
If your GE washer isn't draining, the drain hose might be kinked or improperly connected. Straighten the drain hose, ensuring the washer isn't sitting on it. Also, make sure the top of the drain outlet is less than 8 ft (2.44 m) above the floor.
What to do if water pumped out before cycle is complete in GE Washer?
If the water is pumped out of your GE washer before the cycle is complete, it's possible the previous cycle was cancelled. To resolve this, close the lid, select a new cycle, and start the machine.
How to reduce wrinkling in my GE GTW490AJ?
To minimize wrinkling when using your GE Washer: Select the appropriate cycle for the fabric type, especially for easy-care loads. Avoid mixing heavy items like jeans with lighter items like blouses, and consider using a fabric softener. Do not overload the washer; loosely load clothes in the basket. Wash clothes in warm or cold water to avoid repeated washing in excessively hot water.
Why is my GE GTW490AJ rocking or moving?
If your GE Washer is rocking or moving, it's likely due to uneven leveling legs. Adjust the leveling legs by rotating each leg in the appropriate direction until the washer is stable.
Why does my GE GTW490AJ Washer cause snags, holes, tears, rips or excessive wear?
If your GE Washer is causing snags, holes, tears, rips, or excessive wear on your clothes, consider the following:* Fasten snaps, hooks, buttons, and zippers. Remove loose items like pins, objects in pockets, and sharp buttons. Turn knits (which snag easily) inside out.* Check the bleach package instructions for proper amount. Never add undiluted bleach to wash or allow clothes to come in contact with undiluted bleach.* Rinse items that may have chemicals on them before washing. Use Quick Wash cycle with Extra Rinse option. (on some models)
What to do if there are colored spots on clothes after washing in my GE GTW490AJ Washer?
If you notice colored spots on your clothes after washing them in your GE washer, it could be due to incorrect use of fabric softener. Check the fabric softener package for instructions and ensure you've selected the Deep Rinse option. Dye transfer may also be the cause, so sort whites or lightly colored items separately from dark colors. For stains, pretreat them and rewash using the Speed Wash cycle before drying.
What to do if the water won’t drain from my GE GTW490AJ?
If the water won’t drain from your GE Washer, check that the drain hose is not kinked or that the washer is not sitting on it. Ensure the top of the drain outlet is less than 8 ft (2.44 m) above the floor.
Why are clothes too wet after washing in my GE GTW490AJ Washer?
If your clothes are too wet after washing in your GE Washer, ensure that the selected cycle matches the load type. Some fabrics may feel wetter when rinsed with cold water. If the wash load is out of balance, redistribute the load and run it through a Drain & Spin cycle.
General
