EasyManua.ls Logo

GE GTX33EASK User Manual

GE GTX33EASK
3 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
GTX33EASK
GE Appliances 6.2 Cu. Ft. Capacity
Aluminized Alloy Drum Electric Dryer
For answers to your Monogram, GE Café
Series, GE Profile
Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center
®
Service, 800.626.2000.
Specification Revised 5/16
ELECTRIC DRYER RATING:
240V 5600W 24A 60Hz
208V 4400W 22A 60Hz
EXHAUST OPTION: 4-way rear, right,
left and bottom
CIRCUIT REQUIREMENTS: An
individual, properly-grounded branch
circuit, protected by a 30-amp circuit
breaker or a time-delay fuse, is required.
NOTE: Dryer wall outlet must be
located within 36" of service cord entry
and acessible when dryer is mounted in
position.
INSTALLATION INFORMATION:
For complete information, see installation
instructions packed with your dryer.
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
22 1/2"
26 3/4"
4"
1 3/4"
3 1/4"
4 1/4"
37 1/2"
44"
27"
5"
POWER CORD 4 1/2"
11 3/4"
SIDE VIEW
REAR VIEW
Listed by
Underwriters
Laboratories
SPECIAL INSTALLATION REQUIREMENTS
ALCOVE OR CLOSET INSTALLATION:
- If your dryer is approved for installation in an alcove or closet, it will be stated on a label on
the dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side; 1" front, top and rear
- Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in.
of open area equally distributed. If this closet contains both a washer and a dryer, doors must
contain a minimum of 120 sq. in. of open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of local codes, with the
National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:
- Minimum clearances to combustible surfaces are: 0" both sides; 1" rear
DRYER EXHAUSTING INFORMATION :
Use metal duct only, vertical and horizontal ducting.
Question and Answer IconNeed help?

Do you have a question about the GE GTX33EASK and is the answer not in the manual?

GE GTX33EASK Specifications

General IconGeneral
BrandGE
ModelGTX33EASK
TypeElectric Dryer
Capacity7.2 cu. ft.
ColorWhite
Voltage240 V
Amperage30 A
Weight120 lbs
Drum MaterialAluminized Alloy
Number of Temperature Settings4
Wrinkle Care OptionYes
End of Cycle SignalYes
Energy Star CertifiedNo
Width27 inches
Height44 inches

Summary

Dryer Dimensions and Installation

Dryer Electrical Ratings

Specifies the voltage, wattage, amperage, and frequency for the electric dryer.

Exhaust Options

Details the available directions for dryer exhaust venting (rear, right, left, bottom).

Circuit Requirements

Outlines the necessity of a grounded branch circuit protected by a 30-amp breaker or fuse.

Dryer Wall Outlet Location

Note on dryer wall outlet placement relative to the service cord entry.

Alcove or Closet Installation Requirements

Specifies minimum clearances and ventilation for alcove/closet installations.

Bathroom or Bedroom Installation Requirements

Covers installation conformity with local codes and national standards.

Minimum Clearances (Non-Alcove/Closet)

Defines required clearances to combustible surfaces for other installations.

Dryer Exhausting Information

States that only metal ducting should be used for exhaust.

Dryer Venting and Ducting

Ducting Materials

Details acceptable ducting materials for optimal dryer performance.

Exhaust Length Calculation

Guides on calculating maximum vent length based on turns and duct type.

Exhaust Termination Caution

Warns against improper exhaust termination to prevent fire hazards.

Exhausting Information Table

Provides a table for maximum vent lengths based on turns and hood type.

Dryer Features and Benefits

Drum Material

Highlights the aluminized alloy drum for efficiency and corrosion resistance.

Heat Selections

Describes the availability of multiple drying temperature settings.

Venting Capability

Mentions the dryer's flexible installation due to its venting capacity.

Auto Dry Feature

Explains the automatic drying setting that monitors air temperature.

Control Type

Notes the use of rotary electromechanical controls for setting cycles.

Lint Filter Location

Points out the convenience of the up-front lint filter.

Reversible Door

Mentions the option to reverse the dryer door opening.

Related product manuals