GE HC-PSTN1 - User Manual

To Next Page

GE Healthcare

Smart Patient and

Staff/Duty Stations

HC-PSTN1, HC-PSTN2, HC-CCPSTN

and HC-DUTY

Smart Patient and Staff/Duty Stations are a primary point

of two-way communications between patients and staff.

Equipped with three call buttons and a cancel button, they offer

users an easy-to-operate means of placing calls on the patient-

staff communications system.

With a built-in speaker and microphone, these devices also

provide patients with the means of having a full-duplex

channel of audio communications with attending staff, and

vice versa. On-board LEDs provide operational feedback as

well as status indication.

Smart Patient Stations (HC-PSTN1 & HC-PSTN2) provide separate

18-pin receptacles for the connection of pillow speakers. Each

Smart Patient Station also comes equipped with two 0.64 mm

(0.25 in) receptacles that can be programmed to accept either

an input from auxiliary equipment, or a bed call cord.

Single Smart Patient Stations (HC-PSTN1) provide one set of

connections. Dual Smart Patient Stations (HC-PSTN2) provide

two sets of connections. Smart Staff/Duty Stations (HC-DUTY)

have no bed connections or call cord jacks.

Call Cord Patient Stations (HC-CCPSTN) come equipped with

two 0.64 mm (0.25 inch) receptacles that can be programmed

to accept either an input from auxiliary equipment or a bed call

cord(s). Can be conﬁgured to support one or two patient beds.

All stations provide a NiteLite on-board lighting feature for

easy visibility under low ambient light conditions. They feature

a snap-together design with no mounting screws visible after

installation. Their clean, modern look complements any decor.

Smart Patient and Staff/Duty Stations are installed in

unobstructed areas next to patient beds. Single Smart Patient

Stations serve the needs of one patient. Dual Smart Patient

Stations are installed between two beds and have two sets of

connectors, one for each bed. Smart Staff/Duty Stations are

installed in break rooms and other areas where staff may be

reached. They do not have bed connections.

Calls placed on Smart Patient and Staff/Duty Stations register

and annunciate at ColorTouch VoIP Staff Consoles and

ColorTouch VoIP Annunciators. Connected Inﬁnity LED dome/

zone lights will also operate appropriately depending on the

nature and urgency of the call. These stations also provide full-

duplex audio communications that allow users to speak with

Staff Consoles and Annunciators.

Features

• Integrated call cord and pillow speaker connections

One device, many functions

• NiteLite on-board lighting

Easy visibility under low ambient light conditions

• Dual patient models available

Economical in semi-private room settings

• On-board speaker and microphone

Full duplex operation for intercom use

• Configurable buttons and button labels

Buttons can be individually deﬁned and conﬁgured in the

ﬁeld

• Cleaning mode

Helps to reduce calls when cleaning stations

• Audible, visible and tactile pushbutton feedback

Each press of a button sounds a tone, produces a response

the user can feel, and lights the associated LED

• Mounts to a standard 3-gang ring on a non-masonry box

Simple to install, clean ﬁnished appearance with no visible

screws

• RJ-45 connectivity

Standard plug-in terminations make wiring simple

• No DIP switches to set

Network addressable for easy setup and installation

• Each bed call answered individually

Person-to-person communication helps to ensure privacy

85100-0104; DOC0636754 Rev. 4 (page 1 of 4)

Need help?

Do you have a question about the GE HC-PSTN1 and is the answer not in the manual?

Summary

Smart Patient and Staff;Duty Stations

Product Introduction and System Integration

Overview of Smart Patient and Staff/Duty Stations and their integration with other system components.

Key Features

Highlights integrated functions, lighting, audio, connectivity, and special modes.

Technical Specifications and Installation

Installation Overview and Connectivity

Details on connecting stations to the Telligence LAN/WAN via gateway and network addressability.

Station Connection Types

Describes connection specifics for Single, Dual, Call Cord Patient Stations, and Staff/Duty Stations.

Performance and Power Specifications

Station Functionality and Operation

Explains button functions (CODE, EMERG, ASSIST, CANCEL) and cleaning mode.

Power and Physical Characteristics

Details electrical ratings, power source, dimensions, mounting, construction, and certifications.

Ordering Information

Lists model numbers, descriptions, and shipping weights for various stations and accessories.

The GE Healthcare Smart Patient and Staff/Duty Stations (models HC-PSTN1, HC-PSTN2, HC-CCPSTN, and HC-DUTY) are integral components of a patient-staff communications system, designed to facilitate two-way communication between patients and healthcare staff. These stations serve as primary interface points, equipped with three call buttons and a cancel button, providing an intuitive means for users to place calls within the system.

Function Description:

These stations enable full-duplex audio communication between patients and attending staff, and vice versa, through a built-in speaker and microphone. On-board LEDs provide visual feedback on operational status and call indications. When calls are placed, they register and annunciate at ColorTouch VoIP Staff Consoles and ColorTouch VoIP Annunciators. Additionally, connected Infinity LED dome/zone lights activate, indicating the nature and urgency of the call.

The Smart Patient Stations (HC-PSTN1 and HC-PSTN2) include separate 18-pin receptacles for pillow speaker connections and two 0.64 mm (0.25 in) receptacles programmable for auxiliary equipment input or bed call cords. The HC-PSTN1 (Single Smart Patient Station) offers one set of connections, while the HC-PSTN2 (Dual Smart Patient Station) provides two sets, making it suitable for semi-private room settings. The Call Cord Patient Stations (HC-CCPSTN) are equipped with two 0.64 mm (0.25 inch) receptacles, configurable for auxiliary equipment or one or two bed call cords. Smart Staff/Duty Stations (HC-DUTY) are designed for staff areas like break rooms and do not include bed connections or call cord jacks.

Important Technical Specifications:

Electrical Rating:
- Single Smart Patient Station: 40 VDC, 1.9 W
- Smart Staff/Duty Station: 40 VDC, 1.9 W
- Dual Smart Patient Station: 40 VDC, 2.2 W
Power Source: Telligence Station Gateway
Dimensions (HxWxD): 11.4 x 17.5 x 5.8 cm (4.5 x 6.9 x 2.3 in)
Mounting: Wall mounting, 3-gang ring on a non-masonry box.
Construction: Cycoloy, with a flammability rating of 94 V-0.
Terminations: RJ-45, plus lever-type connectors for TV/Lighting control options.
Indicators: LEDs for CODE, EMERG, CANCEL, ASSIST buttons.
Audio Input: Microphone
Audio Output: Speaker for full-duplex intercom
Controls: Buttons for CODE, EMERG, CANCEL, and ASSIST.
Connectivity: RJ-45 for simple wiring. Network addressable, eliminating the need for DIP switches or jumpers.
Certifications: UL, CSA (22.2 No. 205-M1983).

Usage Features:

Integrated Call Cord and Pillow Speaker Connections: Consolidates multiple functions into one device.
NiteLite On-board Lighting: Ensures easy visibility in low ambient light conditions.
Configurable Buttons and Labels: Buttons can be individually defined and configured in the field, with customizable labels that slide behind a clear button membrane. This allows for flexible functionality, such as initiating a "Code Blue" call (CODE), a staff emergency call (EMERG), or a normal priority call (ASSIST).
Audible, Visible, and Tactile Pushbutton Feedback: Each button press produces an audible tone, a tactile response, and illuminates an associated LED, confirming user input.
Dual Patient Models: Economical for semi-private room settings, allowing two patients to be served by a single station.
Individual Bed Call Answering: Facilitates person-to-person communication, helping to ensure patient privacy.
Automatic Addressing: The system uses an intelligent addressing scheme, eliminating the need for manual DIP switch settings during installation.
Status Indicators: LEDs adjacent to each button indicate the call type. Additional LEDs show the status of auxiliary hardware and, for dual patient stations, which bed originated the call.

Maintenance Features:

Cleaning Mode: An ingenious feature that helps prevent false calls during maintenance. When the station is idle, pressing the CANCEL button for two to four seconds temporarily disables the front panel buttons, allowing maintenance personnel to clean the unit without accidentally placing a call.
Snap-together Design: Facilitates easy installation and maintenance, with no visible mounting screws after installation, contributing to a clean, modern aesthetic.
Mounting: Mounts to a standard 3-gang ring on a non-masonry box, simplifying installation.
Field-replaceable Button Labels: Allows for easy customization and replacement of button labels.

The Smart Patient and Staff/Duty Stations connect to the Telligence LAN/WAN via the Telligence Station Gateway, which also supplies power to the devices. Connections to the gateway are made through associated dome lights, utilizing snap-in RJ-45 connections at both the station and the dome light. This design ensures straightforward setup and installation, with a focus on user-friendliness and reliable communication within healthcare environments.