GE T35 - Page 604

viii T35 TRANSFORMER PROTECTION SYSTEM – INSTRUCTION MANUAL
INDEX
Maintenance
actual values ...................................................................................... 6-25
alert to replace battery ....................................................................7-7
battery replacement ....................................................................10-24
cleaning ................................................................................................ 2-32
commands .............................................................................................7-3
module replacement ....................................................................10-23
upgrade or downgrade ...............................................................10-13
Manufacturing date .......................................................................... 6-25
Maximum CT/VT wire size .............................................................. 3-14
Memory requirements ..................................................................... 3-52
Menu navigation ................................................................................. 4-51
Message about upgrade over Internet ................................10-14
Messages
clear front panel .............................................................................5-254
error ..........................................................................................................7-6
errors and warnings in Engineer .............................................. 4-70
Metering
conventions ............................................................................ 6-12, 6-13
frequency specifications .............................................................. 2-23
power specifications .......................................................... 2-22, 2-23
voltage specifications .................................................................... 2-22
Metering editor ..................................................................................... 4-36
Microsoft Windows requirement ............................................... 3-52
Mimic diagrams ................................................................................... 4-20
MMS connections remaining ....................................................... 6-10
Modbus
connections remaining ................................................................. 6-10
Flex State parameters .................................................................5-130
port, close ............................................................................................ 5-50
register entry ....................................................................................5-108
settings ................................................................................................. 5-49
user map ............................................................................................5-108
Modbus Analyzer ................................................................................ 10-1
Model information, view ................................................................. 6-25
Model number .........................................................................................3-1
Modem connection ............................................................................ 3-62
Modification file number ................................................................. 6-26
Modules
add and check settings not defaulted .................................10-24
communications .............................................................................. 3-30
CT/VT .............................................................................................3-14, 5-6
order codes ......................................................................................... 2-13
power supply ..................................................................................... 3-13
replace ................................................................................................10-23
transducer I/O ................................................................................... 3-28
Monitor
actual values ...................................................................................... 10-1
devices .................................................................................................. 10-1
Mounting ............................................................................................3-2, 3-5
N
Nameplate, rear .....................................................................................3-1
NAND gate explained ....................................................................... 4-84
Navigation keys ................................................................................... 4-38
Non-volatile latches
FlexLogic operands ...................................................................... 5-181
settings ............................................................................................... 5-197
specifications .....................................................................................2-21
NOR gate explained ...........................................................................4-84
NOT gate explained ...........................................................................4-84
O
Obtain list of port numbers ...........................................................5-44
One-shot
error compiling in Engineer .........................................................4-71
FlexLogic operators ...................................................................... 5-186
Operating temperature ...................................................................2-30
Operating times ...................................................................................2-18
Operator command to force logoff .............................................7-4
OR gate explained ..............................................................................4-84
Order codes ...............................................................................................2-7
actual values ......................................................................................6-25
update ..........................................................................................3-61, 7-3
Oscillatory transient testing specifications ..........................2-31
Oscillography
actual values ......................................................................................6-24
clearing ........................................................................................5-39, 7-2
settings ............................................................................................... 5-114
specifications .....................................................................................2-22
via EnerVista software ......................................................................4-2
Out of service ............................................................................................5-1
Outputs
contact outputs ............................................................................. 5-250
control power specifications ......................................................2-27
critical failure relay specifications ............................................2-26
Fast form-C relay specifications ...............................................2-26
Form-A relay ...........................................................................2-25, 3-16
Form-C relay .......................................................................................3-16
Form-C relay specifications ........................................................2-26
latching output specifications ....................................................2-25
latching outputs ............................................................................. 5-251
virtual outputs ................................................................................ 5-254
Overcurrent curve types .............................................................. 5-208
Overcurrent curves
FlexCurves ........................................................................................ 5-213
IAC ........................................................................................................ 5-211
IEC ......................................................................................................... 5-210
P
Panel cutout .................................................................................... 3-2, 3-5
Parallel Redundancy Protocol
actual values ......................................................................................6-11
explained ..............................................................................................5-46
settings ..................................................................................................5-44
specifications .....................................................................................2-28
Parity ..........................................................................................................5-41
Part numbering .......................................................................................2-7