SYSTEM SPECIFICATIONS
AMPLIFIER SECTION CROSSOVER SECTION
Bass amplifier output power with an
4 Ohm load: 180 W
Treble amplifier output power with an
8 Ohm load: 120 W
Long term output power is limited by driver
unit protection circuitry.
Slew rate: 80 V/µs
Amplifier system distortion at
nominal output:
THD < 0.05%
SMPTE-IM < 0.05%
CCIF-IM < 0.05%
DIM 100 < 0.05%
Signal to Noise ratio, referred to full output:
Bass > 100 dB
Treble > 100 dB
Mains voltage: 100/200 V or 115/230 V
Voltage operating range nominal ±10%
Power consumption:
Idle 50 W
Full output 200 W
Input connector: XLR female
pin 1 gnd
pin 2 +
pin 3 -
Input impedance:10 kOhm balanced
Input level for 100 dB SPL output @ 1m:
variable from +6 to -6 dBu
Input level for maximum short term output of
113 dB SPL @ 1m:
variable from +19 to +7 dBu
Subsonic filter below 40 Hz :
18 dB/octave
Ultrasonic filter above 25 kHz:
12 dB/octave
Crossover frequency, Bass/Treble:
1.8 kHz
Crossover acoustical slopes:
24 - 32 dB/octave
Treble tilt control operating range in 2 dB
steps: +2 to -4 dB & MUTE
Bass roll-off control operating range in 2 dB
steps: 0 to -8 dB @ 40 Hz
Bass tilt control operating range in 2 dB
steps: 0 to -6 dB & MUTE
The 'CAL' position is with all tone controls
set to 'off' and input sensitivity control to
maximum.
Lower cut-off frequency, -3 dB: < 40 Hz
Upper cut-off frequency, -3 dB: > 22 kHz
Free field frequency response of system:
42 Hz - 21 kHz (± 2.5 dB)
Maximum short term sine wave acoustic
output on axis in half space, averaged from
100 Hz to 3 kHz:
@ 1m > 113 dB SPL
@ 0.5m > 119 dB SPL
Maximum long term RMS acoustic output in
same conditions with IEC weighted noise
(limited by driver unit protection circuit):
@ 1m > 103 dB SPL
@ 0.5m > 109 dB SPL
Maximum peak acoustic output per pair on
top of console, @ 1 m from the engineer
with music material: > 124 dB
Self generated noise level in free field @ 1m
on axis: < 10 dB (A)
Harmonic distortion at 90 dB SPL @ 1m on
axis:
Freq: 50...100 Hz < 1%
> 100 Hz < 0.5%
Drivers:
Bass 250 mm (10") cone
Treble 25 mm (1") metal dome
Both drivers are magneti-
cally shielded
Weight: 21,7 kg (48 lb)
Dimensions: Height 495 mm (19
1
/
2
")
Width 320 mm ( 12
5
/
8
")
Depth 290 mm (11
7
/
16
")
1032A
Genelec Oy, Olvitie 5
FIN - 74100 IISALMI, FINLAND
Phone: +358 - 17 - 83 881
Fax: +358 - 17 - 812 267
E-mail: genelec@genelec.com
Web: http://www.genelec.com
Genelec Inc, 7 Tech Circle
Natick, MA 01760, USA
Phone: +1 - 508 - 652 - 0900
Fax: +1 - 508 - 652 - 0909
E-mail: genelec.usa@genelec.com
Genelec Document BBA32001a COPYRIGHT GENELEC OY 6.2000
All data subject to change without prior notice
Gen 1032A Data Sheets 27.6.2000, 12:414
To Previous Page
Loading...
Need help?
General
