8020A Data Sheet
Genelec Document BBA0034001 Copyright Genelec Oy 9.2005. All data subject to change without prior notice
International enquiries:
Genelec, Olvitie 5
FIN-74100, Iisalmi
Finland
Phone +358 17 83881
Fax +358 17 812 267
Email genelec@genelec.com
In the U.S. please contact
Genelec, Inc., 7 Tech Circle
Natick, MA 01760
Phone +1 508 652 0900
Fax +1 508 652 0909
Email genelec.usa@genelec.com
www.genelec.com
AMPLIFIER SECTION
CROSSOVER SECTION
SYSTEM SPECIFICATIONS
8020A
Lower cut-off frequency, -3 dB < 65 Hz
Upper cut-off frequency, -3 dB > 21 kHz
Free field frequency response
66 Hz – 20 kHz (± 2.5 dB)
Maximum short term sine wave acoustic
output on axis in half space, averaged
from 100 Hz to 3 kHz @ 1 m
> 96 dB SPL
@ 0.5 m
> 102 dB SPL
Maximum long term RMS acoustic
output in same conditions with
IEC-weighted noise (limited by driver
unit protection circuit) @ 1 m
> 95 dB SPL
Maximum peak acoustic output per pair
@ 1 m from the engineer with music
material
> 105 dB
Self generated noise level in free field
@ 1 m on axis
< 10 dB (A-weighted)
Harmonic distortion at 85 dB SPL Freq: 50...100 Hz < 3 %
@ 1 m on axis > 100 Hz < 0.5 %
Drivers Bass
105 mm (4") cone
Treble
19 mm (
3
/
4
") metal dome
Both drivers are magnetically shielded
Weight 3.7 kg (8.1 lb)
Speaker dimensions Height 242 mm (9
1
/
2
")
(including Iso-Pod table stand)
Height 230 mm (9
1
/
16
")
(without Iso-Pod table stand)
Width 151 mm (6")
Depth 142 mm (5
5
/
8
").
8020A
Bass amplifier output power Short term 20 W (8 Ohm load)
Treble amplifier output power Short term 20 W (8 Ohm load)
Long term output power is limited by driver unit
protection circuitry.
Amplifier system distortion at THD
<0.08 %
nominal output SMPTE-IM
<0.08 %
CCIF-IM
<0.08 %
DIM 100
<0.08 %
Signal to Noise ratio, Bass
>95 dB
referred to full output Treble
>95 dB
Mains voltage:
100, 120, 220 or 230 V according to region.
Voltage operating range: ±10 %
Power consumption Idle 5 VA
Full output 50 VA
8020A
Input connector: XLR female, pin 1 gnd, pin 2 +, pin 3 -
balanced 10 kOhm
Output connector: XLR male, pin 1 gnd pin 2 +, pin 3 -
balanced 100 Ohm
Input level for 100 dB SPL output @ 1m
-6 dBu at volume control max
Volume control range -80 dB relative to max output
Output signal level is 0 dB relative to input signal level
but adjustable by volume control
Crossover frequency 3.0 kHz
Treble tilt control operating range 0 to –2 dB @ 15 kHz
Bass roll-off control –6 dB step @ 85 Hz
(to be used in conjunction with a 7050B subwoofer)
Bass tilt control 0 to –6 dB @ 100 Hz in 2 dB steps
The ‘CAL’ position is with all tone controls set to ‘off’
and input sensitivity control to maximum and
corresponds to a maximally flat free field response.
Figure 3: The upper curve group shows the horizontal directivity char-
acteristics of the 8020A measured at 1 m. The lower curve shows the
systems power response.
Figure 4: The curves above show the effect of the “bass tilt”, “treble tilt”
and “bass roll-off” controls on the free field response.
In Sweden please contact
Genelec Sverige
Ellipsvägen 10B
P.O. Box 5521, S-141 05 Huddinge
Phone +46 8 449 7070
Fax +46 8 708 7071
Email info@genelec.com
In China please contact:
Beijing Genelec Audio Co. Ltd.
Jianwai SOHO, Tower 12, Room 2306
39 East 3rd Ring Road
Chaoyang District, Beijing 100022
Phone +86 10 5869 7915
Fax +86 10 5869 7914
To Previous Page
Loading...
