8030A Active Monitoring System
The Genelec 8030A is a very compact bi-
amplified active monitor system with perfor-
mance comparable to much larger systems.
The 8030A excels in applications where space
is at a premium, taking full advantage of the
unconventional design and advanced technol-
ogies of Genelec’s 8000 Series loudspeaker
range. The all-aluminium Minimum Diffraction
Enclosure™ (MDE™) and advanced Directivity
Control Waveguide™ (DCW™) technologies
are carefully matched with advanced amplifier
and electronics circuitry and the latest drivers.
Bass response has been widened down to
55 Hz (-3 dB) while distortion is substantially
lower due to a uniquely new rear reflex port
design. The system's excellent directivity char-
acteristics and accurate imaging together with
its compact size and flexible mounting options
make the 8030A the perfect monitoring tool for
a wide range of applications.
The 8030A has been specially designed to
have a sufficient LF extension for most situ-
ations. However if greater SPL's and a lower
cutoff frequency are required, it can be com-
plemented with Genelec 7050B subwoofer,
which has a lower cutoff point of 25 Hz.
Integrated construction
The 8030A is very easy to set up and use,
the only connections required are the mains
supply and the line level input. The input is
made via a balanced female XLR. A balanced
male XLR output connector can be used
for connecting a 7050B subwoofer or daisy
chaining up to six 8030A’s together.
The volume control is located on the front
panel. This allows easy level matching with
other audio equipment.
The integrated design allows the amplifiers
and the drivers to be calibrated as a single
unit, eliminating the effects of component tol-
erances and ensuring consistent quality.
Crossover filters
The amplifier unit contains an active cross-
over, a feature more commonly used in large
and expensive control room monitors. This
is the ideal method for dividing the input
signal between the driver units. The active
crossover allows the overall response of the
system to be optimized to an extent impos-
sible with a passive system. To maintain uni-
form frequency balance in differing acoustic
environments, special calibrated controls are
included in the active crossover network.
These controls include “treble tilt”, “bass tilt”
and “bass roll-off” switches.
Amplifiers
The bass and treble amplifiers produce
40 W of output power each, with very low THD
and IM distortion values. The amplifiers are
designed to ensure the highest subjective
sound quality currently possible. The ampli-
fier unit also contains a protection circuit that
monitors the output levels and prevents any
damage to the drivers. This makes the system
immune to overloads and spurious signals.
Drivers
A 19 mm (
3
/
4
") metal dome tweeter is loaded
by an advanced DCW™ waveguide. The
DCW™ is integrated into the one piece front
baffle.
The 130 mm (5") bass cone driver is
mounted in a newly designed bass reflex
enclosure. The long, flow optimized reflex
tube has a large cross sectional area and
terminates with a wide flare at the back of
the enclosure.
Protective grilles are positioned in front of
both drivers. Magnetic shielding is standard
on the 8030A. Shielding is vital for applica-
tions such as video post production, where
stray magnetic fields must be minimized.
MDE™ and DCW™
Technologies
The Minimum Diffraction Enclosure™
(MDE™) Technology increases the perfor-
mance of the Genelec 8000 Series loud-
speakers by minimizing edge diffraction and
improving frequency and power response.
The edges of the enclosure are rounded and
Applications
• NearFieldMonitoring
• AudioVideoPostProduction
• MobileVans
• HomeTheaters
• Project/HomeStudios
• DigitalWorkstations
• MultimediaProductionand
Playback
System
To Next Page
Loading...
Need help?
General
Weight and Dimensions
