Generac Power Systems 0065781 - Page 61

EXPLODED VIEW: EV MTG BASE G6.8 B-GRP SSS Y02 PAN
DRAWING #: 0K0287D GROUP C
APPLICABLE TO: CO 1496255
ITEM PART# QTY. DESCRIPTION
REVISION: K-2638-F Page 2 of 2
DATE: 4/29/15
(1)1 0K0284DST0R 1 MTG BASE G6.8 B_GRP SSS Y02 w/ PAN
2 024310 1 PLUG STD PIPE 1/2 STEEL SQ HD
3 052252 4 DAMPENER VIBRATION
4 052257 4 SPACER .49 X .62 X 1.87 PWDR/ZINC
5 052259 4 WASHER FLAT M12
6 055597 4 SCREW HHC M12-1.75 X 85 G8.8
7 052251A 4 DAMPENER VIBRATION 50 WHITE
8 052860 4 NUT LOCKING M12-1.75
(1)9 0L07030ST0R 1 ENGINE SUPPORT 6.8L RH
(1)10 0L02440ST0R 1 ENGINE MOUNT 6.8L LH
11 0E3865 1 DECAL ENVIROMENTAL WARNING
12 051756 1 SCREW HHC M10-1.5 X 20 C8.8
13 046526 9 WASHER LOCK M10
14 022131 9 WASHER FLAT 3/8-M10 ZINC
15 025507 2 WASHER LOCK EXT 7/16 STL
16 038805G 1 CABLE BATT BLK #1 X 41.50 NEG
17 096500V 1 ASSY FUEL LEAK DET ALARM W/CON
18 050277A 1 DECAL OIL DRAIN TRI
19 075763 1 BOOT BATTERY CABLE
20 038804AG 1 CABLE BATT RED #1 X 50.00
21 050331A 1 BATT POST COVER RED +
22 049813 1 NUT HEX M6-1.0 G8 CLEAR ZINC
23 0A1658 1 WASHER LOCK SPECIAL 1/4"
24 022097 1 WASHER LOCK M6-1/4
25 051735 4 SCREW HHC M10-1.5 X 70 C8.8
26 052243 4 SCREW HHC M10-1.5 X 60 C8.8
27 050331 1 BATT POST COVER BLK -
28 022473 1 WASHER FLAT 1/4-M6 ZINC
29 030985 1 NIPPLE CLOSE 1/2 X 1.125
30 0G5212A 1 VALVE 1/2"
31 044118 1 BARBED STR 1/2NPT X 5/8
32 0G0015 2 CLAMP HOSE 7/8" OD DOUBLE WIRE
33 065386 1 HOSE 5/8 ID SAE100R6 (21”LG)
34 034339 1 BARBED EL 90 3/8NPT X 5/8
35 057765 1 ADP OIL DRN M14-1.50
36 057772 1 WASHER NYLON .565
37 0536210360 1 WIRE ASSEM #4GA GRD
38 045757 1 SCREW HHC M6-1.0 X 25 C8.8
39 026924 1 ELBOW 90D STREET 3/8
(1)40 0L01390ST0R 1 5.4L RH ENGINE MOUNT SPACER
KIT VARMINT GUARD P/N 0L3582
A 0A8785 4 PLUG, BUTTON 3" DIA.
NOTES (UNLESS OTHERWISE SPECIFIED):
(1) SHEET METAL PARTS LISTED IN THE BOM TABLE ARE REPRESENTING GENERIC PARTS (NO COLOR)
• MANUFACTURING: FOR CORRECT MATERIAL AND COLOR REFER TO AS400 BOM.
• CUSTOMER: WHEN ORDERING REPLACEMENT PARTS ENTER BASE NUMBER (FIRST 6 DIGITS ONLY)
IN THE SYSTEM FOR CORRECT MATERIAL AND COLOR (FOR REFERENCE SEE GUIDELINE 0H7169).