Generac Power Systems 006719-0 User Manual (English)

Questions and Answers:

D
Dakota MiddletonAug 17, 2025
How to fix a Generac Power Systems 006719-0 Portable Generator that won't start?
- D
  Daniel KimAug 17, 2025
  If your Generac Power Systems Portable Generator won't start, here are a few things to check: * Make sure there is fuel in the tank; if not, add fuel. * Ensure the fuel valve is turned on. * Inspect the spark plug for defects and replace if necessary. * Replace the fuel filter if it's plugged. * Consider replacing the engine start switch if it's defective or stuck.
J
jsanchezAug 20, 2025
Why does my Generac Power Systems 006719-0 Portable Generator start then shut down?
- P
  preston21Aug 20, 2025
  Your Generac Power Systems Portable Generator might start and then shut down due to several reasons: * Low fuel level: Add fuel to the tank. * Closed fuel tank vent: Open the fuel tank vent. * Incorrect engine oil level: Check and adjust the engine oil level as needed. * Contaminated fuel: Replace the fuel filter. * Defective low oil level switch: Replace the low oil level switch. * Defective ignition coil: Replace the ignition coil.
L
Lynn CookAug 22, 2025
What to do if Generac Power Systems 006719-0 starts, then runs rough?
- B
  Brooke ConleyAug 22, 2025
  If your Generac Power Systems Portable Generator starts but runs rough, consider the following: * Check if the choke is stuck or left on; if so, turn it off. * Inspect the air filter for dirt or clogs; clean or replace it as necessary. * Replace the spark plug if it's defective or dirty. * Replace the fuel and fuel filter if the fuel filter is dirty. * Replace the EcoMode switch if it's defective.
D
drobinsonAug 26, 2025
Why is there no AC output from my Generac Power Systems 006719-0 Portable Generator?
- K
  Kristen KleinAug 26, 2025
  If there's no AC output from your Generac Power Systems Portable Generator, check these: * Overload: Shut down the generator to reset the module, reduce the load, and restart. * Low AC voltage: Verify that the choke is OFF. * Overheated inverter module: Ensure the service door is ON, let it cool for 15 minutes, and restart. * Short circuit: Verify the condition of extension cords and powered items. * Defective inverter assembly: Replace the inverter assembly.
A
Amanda BurnsAug 28, 2025
What to do if there is no DC output from Generac Power Systems Portable Generator?
- D
  Darren SmithAug 28, 2025
  If your Generac Power Systems Portable Generator has no DC output: * Reset the DC circuit breaker if it's open. * Replace the DC circuit breaker if it's defective. * Replace the rectifier if it's defective.
L
Lisa TorresAug 31, 2025
Why does fuel leak from the drain hoses of my Generac Power Systems 006719-0 Portable Generator?
- M
  Matthew SteeleAug 31, 2025
  If fuel leaks from the drain hoses of your Generac Power Systems Portable Generator: * The fuel system may be over-primed (flooded): Let the generator sit for 15 minutes before restarting. * The carburetor drain in the bowl may not be closed: Turn the valve clockwise to close it.
K
Kerri ShawSep 2, 2025
Why won't my Generac Power Systems Inverter engine start?
- M
  Michael FrostSep 2, 2025
  If your Generac Power Systems Inverter engine won't start, it could be due to several reasons. First, ensure there is fuel in the tank by adding fuel if needed. Next, check that the fuel valve is turned on. If these steps don't work, the spark plug may be defective and require replacement, or the fuel filter might be plugged, necessitating its replacement. Finally, a defective or stuck engine stop switch could be the culprit, which would require replacing the engine start switch.
E
Elizabeth KnightSep 5, 2025
What to do if Generac Power Systems Inverter starts, then shuts down?
- W
  warnercharlesSep 5, 2025
  If your Generac Power Systems Inverter starts but then shuts down, it could be due to several factors. Begin by adding fuel to the tank if the fuel level is low. Ensure the fuel tank vent is open. Check the engine oil level and add oil if needed. Consider replacing the fuel filter in case of contaminated fuel. A defective low oil level switch or a defective ignition coil may also cause this issue, requiring replacement of the engine start switch or the ignition coil, respectively.
L
Lawrence SandovalSep 8, 2025
How to fix a Generac Power Systems Inverter that starts, then runs rough?
- P
  pattyholmesSep 8, 2025
  If your Generac Power Systems Inverter engine starts but runs rough, it might be because the choke is stuck or left on; in this case, turn the choke off. Another cause could be a dirty or clogged air filter, so clean or replace the air filter element. Also, a defective spark plug, a dirty fuel filter, or a defective FlexPower switch could be the reason. Replace the spark plug, fuel filter, or FlexPower switch as needed.
L
Larry BrownSep 12, 2025
What causes no AC output from a Generac Power Systems Inverter?
- A
  Amy LamSep 12, 2025
  If your Generac Power Systems Inverter has no AC output, it could be due to the generator being overloaded, indicated by the LED being on. Reduce the load and restart the generator. Alternatively, the inverter assembly may be defective and need replacement.

Generac Power Systems 006719-0 Specifications

General

Model Number	006719-0
Category	Portable Generator
Fuel Type	Gasoline
Starting System	Electric/Recoil
Frequency	60 Hz
AC Output	120/240V
Voltage	120V
Wheel Kit	Included