Generac Power Systems 0065781 - Page 71

EXPLODED VIEW: EV COOLING SYSTEM 6.8L TELECOM
DRAWING #: 0J2567A GROUP D
APPLICABLE TO:
ITEM PART# QTY. DESCRIPTION
REVISION: K-2628-G Page 2 of 2
DATE: 4/24/15
(1)1 0J06070ST0R 1 RADIATOR SUPPORT LH 6.8L
(1)2 0J06060ST0R 1 RADIATOR SUPPORT RH 6.8L
3 0G1286A 1 RADIATOR, R/H-IN L/H-OUT
4 046627 1 CAP RADIATOR 14PSI
5 0D3520 1 HOSE, LOWER RADIATOR
6 0D3521 1 HOSE, UPPER RADIATOR
7 042561 2 CLAMP HOSE #36 1.88 - 2.75
(1)8 0J06270ST0R 1 ASSY VENTURI 6.8L B/C-GRP
9 042907 7 SCREW HHC M8-1.25 X 16 C8.8
10 051768 6 SCREW HHC M12-1.75 X 25 C8.8
11 049808 6 WASHER FLAT M12
12 052860 6 NUT TOP LOCK FL M12-1.75
13 052250 2 TAPE FOAM 1 X 1 (27"LG)
14 090388 1 SCREW HHTT M6-1.0 X 12 ZINC
15 0D2149 1 SPACER, FAN 6.8L
16 0D7975 1 WATER BOTTLE BRACKET
17 076749 1 TANK COOLANT RECOVERY
18 048031C 3 CLAMP HOSE BAND 1/4
19 029032 1 HOSE 9/32 ID (31"LG)
20 0D3293A 1 FAN, COOLING 22" DIA KYSOR
21 046526 6 WASHER LOCK M10
22 022131 6 WASHER FLAT 3/8-M10 ZINC
23 045771 8 NUT HEX M8-1.25 G8 CLEAR ZINC
24 022129 20 WASHER LOCK M8-5/16
25 0C2454 3 SCREW HWHT M6-1 X 16 N WA Z/JS
26 0F2776A 1 BRACKET, SIGNAL CONDITIONER
27 0H1827 1 PROBE COOLANT LEVEL 3/8-18NPTF
28 022145 8 WASHER FLAT 5/16-M8 ZINC
29 049814 6 SCREW HHC M10-1.5 X 25 C8.8
30 0G7895B 1 HARN RADIATOR GND 46"
31 077043H 1 CONDUIT FLEX .25"ID (46”LG)
32 0A4456 1 WASHER LOCK SPECIAL 3/8
33 022142 4 SCREW HHC 5/16-18 X 3/4 G5
34 0H3852 1 HOSE HOLDER PLASTIC (.4-.5 ID)
35 065852 1 SPRING CLIP HOLDER .37-.62
36 036865 1 DRAINCOCK 41.8LG BRASS
37 0C7649 2 CLAMP HOSE .38-.87
38 047290 1 HOSE 3/8 ID SINGLE BRAID (40”LG)
39 039253 1 SCREW HHC M8-1.25 X 20 C8.8
40 050276 1 DECAL RADIATOR DRAIN
41 055934M 1 CLAMP STL/VNL .75 X .343 Z
42 035685 2 CLAMP HOSE #28 1.32-2.25
43 029032 1 HOSE 9/32 ID (42” LG)
44 085662 3 TIE WRAP UL 14.6 X .14 BLK (NOT SHOWN)
45 057593 3 CABLE TIE MOUNT (NOT SHOWN)
NOTES (UNLESS OTHERWISE SPECIFIED):
(1) SHEET METAL PARTS LISTED IN THE BOM TABLE ARE REPRESENTING GENERIC PARTS (NO COLOR)
• MANUFACTURING: FOR CORRECT MATERIAL AND COLOR REFER TO XA BOM.
• CUSTOMER: WHEN ORDERING REPLACEMENT PARTS ENTER BASE NUMBER (FIRST 6 DIGITS ONLY) IN THE SYSTEM
FOR CORRECT MATERIAL AND COLOR (FOR REFERENCE SEE GUIDELINE 0H7169).
(2) FASTEN HOSE TO VENTURI USING TIE WRAP I/N 44 AND CABLE TIE MOUNTS I/N 45. DIRECT HOSE TOWARDS THE
BOTTOM OF UNIT AND AWAY FROM EXHAUST COMPONENTS.