Need help?Do you have a question about the Generac Power Systems H-100 and is the answer not in the manual?
General| Brand | Generac Power Systems |
|---|---|
| Model | H-100 |
| Category | Control Panel |
| Language | English |
Comprehensive safety guidelines for installation, operation, and servicing.
Procedures for configuring the H-100 Control Panel and its settings.
Options for tailoring the controller's functions and parameters via GenLink.
Core system module processing all physical inputs and measurements.
Details on the 23 analog channels, their fixed functions, and spares.
Configuration of alarms and warnings for analog inputs, including setpoints and delay times.
Settings for event logging, analog outputs, and sensor ratings.
Flags and flags used to indicate status for alarms, messages, and ILC inputs.
Availability and use of spare analog input channels for custom measurements.
Controls engine cranking, starting, running, and stopping based on rules.
Configuration settings for engine flywheel teeth, CT ratio, phase, and RPM.
Parameters related to engine operation, including preheat, crank, and warmup times.
Settings for automatic voltage regulation, including KP/KI/KD, VF corners, and AVR dump.
Settings for automatic frequency regulation, including actuator types and soft start.
Options for monitoring and logging parameters over time, locally or remotely.
Setup and usage of remote data monitoring via GenLink.
On-board data logging and trending capabilities.
Integrated Logic Controller for generating outputs and basic generator control.
Overview of the control panel's dual LCD displays and keypad layout.
Fixed parameter pages available on the left display.
Menu-driven pages accessible via the keypad on the right display.
System alarm and warning pages, displaying current and recent fault conditions.
Shows three-phase and single-phase system voltage and current readings.
Visual representation of the utility and generator switch positions.
Displays the last 20 alarms or warnings with timestamps.
Shows total system real, reactive, and apparent power, plus power factor.
Graphical representation of generator frequency over the last 10 seconds.
How to navigate through the various menu pages on the right display.
Detailed view of alarm/warning messages, status, and acknowledgment.
Displays various engine operating parameters and sensor readings.
Specific engine parameters like RPM, battery voltage, and throttle position.
Displays system status, time, and versions, including engine and generator states.
Maintenance status items and display contrast adjustment.
Displays voltage, power, and i2t parameters for the generator.
Graphical display of alternator thermal limit percentage and related parameters.
Access to digital inputs, outputs, analog inputs, and communication status diagnostics.
Lists and describes digital inputs and outputs with their assigned functions.
Displays raw unprocessed data for analog input channels.
Details on RS-232 and RS-485 ports, Modbus configuration, and modem options.
Describes the benefits and setup of weekly generator exercise modes.
Step-by-step guide to configuring QuietTest® mode via GenLink software.
Configuring standard weekly exercise schedules using GenLink software.
Configuring QuietTest® mode directly on the control panel display.
Configuring standard exercise schedules via the control panel display.
Functionality for scheduling internal exercise and timestamping logs.
Procedure to set date and time via the GenLink software interface.
Procedure to set date and time directly on the control panel.
How to adjust the screen contrast for optimal viewing.
Enabling control of HTS units via the H-100 Control Panel.
Configuring HTS parameters and settings using GenLink software.
Configuring HTS parameters and settings directly on the control panel.
Connecting remote annunciator panels to the RS-485 bus.
Overview and requirements for the updated GenLink software.
Detailed explanation of analog input functions, coefficients, and conversions.
Comprehensive listing of H-100 analog inputs, outputs, and connector pin assignments.
List of analog inputs, their default signal names, types, and connector pins.
List of digital outputs, their signal descriptions, and connector pins.
List of digital inputs, their default signal names, and connector pins.
Detailed mapping of digital output numbers to their default function names and descriptions.
Detailed breakdown of signals and their corresponding pins for J1 and J2 connectors.
Explanations for various internal alarms and warnings generated by the H-100 panel.
To Next Page
