EasyManua.ls Logo

Gewiss RESTART PRO User Manual

Gewiss RESTART PRO
8 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
1
L2
L1
2
L3
N
400V~
L2L1
LOAD
L3 N
1
4
OFF
AUX
2 Nm
5
2 Nm
3
≤35
mm
2
≤35
mm
2
≤0,4 Nm
7
≤2,5 mm
6
2
RESTART / AUTOTEST PRO
I N T E R R U T T O R E C O N R I C H I U S U R A A U T O M AT I C A P R E V I A V E R I F I C A D E L L I M P I A N T O E
FU NZ IO NE DI A UT OT ES T DE L D I F F E R E N Z I A L E S EN ZA INT ER RU ZI ON E D E L LAL IM EN TA ZI ON E
RCCB RECLOSING DEVICE WITH P REVI OUS CONTROL OF THE INSTALLAT ION AND SELF TEST FUNCTION
I N T E R R U P T E U R AV E C R E - F E R M E T U R E A U T O M AT I Q U E A P R È S V É R I F I C AT I O N D E L ' I N S TA L L AT I O N ,
E T F O N C T I O N D ' A U T O T E S T D U D I F F É R E N T I E L S A N S C O U P E R L ' A L I M E N T A T I O N
I N T E R R U P T O R C O N C I E R R E A U T O M Á T I C O P R E V I O C O N T R O L D E L A I N S T A L A C I Ó N Y
F U N C I Ó N D E A U T O T E S T D E L D I F E R E N C I A L S I N I N T E R R U P C I Ó N D E L A A L I M E N T A C I Ó N
S C H A L T E R M I T A U T O M A T I S C H E M S C H L I E S S E N N A C H Ü B E R P R Ü F U N G D E R A N L A G E U N D
S E L B S T T E S T D E S F I - S C H U T Z S C H A LT E R S O H N E U N T E R B R E C H U N G D E R S T R O M V E R S O R G U N G
I N T E R R U P T O R C O M F E C H O A U T O M Á T I C O C O M V E R I F I C A Ç Ã O P R É V I A D A I N S TA L A Ç Ã O E
F U N C I O N A M E N T O D E A U T O T E S T E D O D I F E R E N C I A L S E M I N T E R R U P Ç Ã O D A A L I M E N T A Ç Ã O
INSTALLAZIONE
-
INSTALLATION
-
INSTALLATION
-
INSTALACIÓN
-
INSTALLATION
-
INSTALAÇÃO
L’interruttore differenziale non può essere alimentato dal basso.
The RCCB can not be supplied from below.
Le interrupteur différentiel ne peut pas être alimenté par le bas.
El interruptor diferencial no puede ser alimentado desde abajo.
Der FI-Schutzschalter kann nicht von unten versorgt werden.
O interruptor diferencial não pode ser alimentado por baixo.
Carico - Load - Charge
Carga - Last -Carga
Carico - Load - Charge
Carga - Last -Carga
L3
L2
L1
N
LINE
RESTART
AUTOTEST
AUX
LOAD
LOAD
AUX
L3
L2
L1
N
NO!
RESTART
AUTOTEST
LINE
Intervenire solo ad
impianto se zio nato e
quindi con dispositivo non
inserito (vetrino spostato a destra e
leva accessibile)
Intervention is only permitted when
the unit is isolated and the device has
been switched off (slide moved to the
right and lever accessible)
Nintervenir qu'avec linstallation
sectionnée et donc avec le dispositif
non branché (verre déplacé
sur la droite et levier accessible).
Actuar solo con la instalación
seccionada y por lo tanto con
dispositivo no activado (placa de vidrio
hacia la derecha y palanca accesible)
Nur an der Anlage arbeiten, wenn diese
getrennt ist, d.h. mit ausgeschaltetem
Gerät (Scheibe nach rechts geschoben
und Hebel zugänglich)
Intervir somente com a instalão
cortada e, portanto, com dispositivo
desactivado (lâmina deslocada à
direita e alavanca acessível)
90
Question and Answer IconNeed help?

Do you have a question about the Gewiss RESTART PRO and is the answer not in the manual?

Gewiss RESTART PRO Specifications

General IconGeneral
TypeAutomatic Reclosing Device
ModelRESTART PRO
BrandGewiss
Rated Voltage230/400 V AC
Voltage Rating230/400 V AC
Tripping CurveC
Breaking Capacity6 kA
Protection DegreeIP20
MaterialThermoplastic
Mounting TypeDIN Rail
Poles2P, 4P
StandardsIEC/EN 61009-1
Number of Poles2P, 4P
Rated Current6A to 63A
Current Rating6A to 63A

Summary

Automatic Reset Test

Initial Commissioning and Reset Test

Explains the initial setup and procedure for the automatic reset test.

RCCB Trip Scenarios and Status

Untimely Tripping and Fault Conditions

Details causes and indicators for untimely tripping and earth faults.

Reset Status and LED Indicators

Explains device status based on LED indicators like fixed or flashing red.

LED Signal Indicators

LED Status and Meanings (Restart/Autotest OFF)

Interprets LED signals for the device in the Restart/Autotest OFF state.

LED Signal Indicators (Continued)

Troubleshooting and Auxiliary Contact Configuration

Auxiliary Contact Configuration Modes

Details the different modes for configuring the auxiliary contact.

Technical Specifications

Related product manuals