To Next PageTo Next PageWhat to do if I hold the on/off button but can't start the Gima Pet Care Product?
If your Gima Pet Care Product won't start even when holding the on/off button, there are a couple of things to check: * The batteries might be exhausted; replace all four with new ones. * The battery polarities might be reversed; double-check the battery installation to ensure they are placed correctly.
What to do if Gima Measuring Instruments won't start when holding the power button?
If your Gima Measuring Instruments device doesn't start when you hold the power button, it could be due to exhausted batteries or reversed battery polarities. Replace all four batteries with new ones and check the battery installation to ensure proper placement according to the polarities.
What to do if there is no pressure in Gima Measuring Instruments?
If there is no pressure in your Gima Measuring Instruments device, it could be due to a cuff leakage, the cuff windpipe not being correctly connected, or the cuff not being inflated. You may need to buy a new cuff or correctly connect the cuff windpipe with the cuff. If the cuff is not inflated, stop using the device and contact us.
What causes overpressure in Gima Measuring Instruments?
Overpressure in Gima Measuring Instruments can occur if the cuff is blocked or squeezed. To resolve this, ensure the cuff is correctly connected.
What does 'Excessive movement Over range Saturated signal' mean on Gima Measuring Instruments?
This message on your Gima Measuring Instruments indicates that the signal extent is too big because of movement during measurement. Keep your limbs and body still, and then measure again.
Why does Gima Measuring Instruments power off suddenly when inflating?
If your Gima Measuring Instruments device powers off suddenly during inflation, it may be because the batteries have been depleted due to prolonged disuse or temperature changes. Replace all four batteries with new ones.
What to do if Gima CONTEC08A-VET can't measure when pressing the button?
If your Gima Pet Care Product won't start a measurement when you press the measurement button, try switching the power off and on again and then restart the measurement.
Why does my Gima CONTEC08A-VET power off suddenly when inflating?
If your Gima Pet Care Product powers off suddenly while inflating, it's likely because the batteries have been depleted from not being used for a long time. Replacing all four batteries with new ones should resolve this issue.
Why are the BP measurement values too high or too low on my Gima CONTEC08A-VET?
If you're getting BP measurement values that are too high or too low on your Gima Pet Care Product, it could be due to a couple of reasons. First, the cuff might not be connected correctly; ensure it's properly connected. Second, moving your limbs during measurement can also cause inaccurate readings; keep still and restart the measurement.
What to do if Gima Measuring Instruments cuff never deflates?
Pull out the cuff to deflate. Stop using the device and contact us.
General| Model | CONTEC08A-VET |
|---|---|
| Category | Pet Care Product |
| Measurement Method | Oscillometric |
| Resolution (Blood Pressure) | 1 mmHg |
| Accuracy (Blood Pressure) | ±3 mmHg |
| Overpressure Protection | Yes |
| Product Type | Veterinary Blood Pressure Monitor |
| Accuracy (Temperature) | ±0.2°C |
| Resolution (Temperature) | 0.1°C |
| Memory Function | Yes |
| Auto Power Off | Yes |
| Waterproof | No |
| Applicable object | Dog, cat and other types of animals |
| Battery Type | AA |
| Probe Cover | Not applicable |
| Dimensions | 130mm x 110mm x 80mm |
| Weight | 300 g |
Steps for installing AA dry batteries, including polarity and battery cover closure.
Instructions for connecting and using the AC adapter with the device.
Details on technical alarms, such as low power, and how they are managed.
Guidelines for correct limb placement and measurement consistency for accurate results.
Steps to start, stop, and confirm a blood pressure measurement using the device.
How to access and view previously recorded blood pressure and pulse rate measurements.
Procedure for clearing all measurement results from the device's memory.
