Why is the dried linen moisture level too high in my GIRBAU ED260?
If the dried linen has a high moisture level, it could be due to a few reasons: * There may be excessive residual moisture in the fabrics, so adjust the spin process. * The drying time may be insufficient, so alter the program to increase the drying time. * The temperature might be too low, so alter the program to increase the temperature.
What to do if the burner can not be ignited in my GIRBAU gas Dryer?
If the burner in your GIRBAU gas dryer won't ignite: * First, check if the manual gas flow valve is closed and open it. * If that's not the issue, a registered installation contractor should check the gas supply pressure and flow rate. If the problem persists, contact the Authorised Technical Services.
Why is the flame too orange in my GIRBAU gas Dryer?
An orange flame in your GIRBAU gas dryer could be caused by: * A faulty air intake filter, so clean the filter. * A poor air/gas mixture, so check, and if necessary correct, the position of the venturi. If the problem persists, contact the Authorised Technical Services.
What causes poor flame spread in my GIRBAU gas Dryer?
Poor flame spread in your GIRBAU gas dryer could be due to: * Insufficient gas supply, so ask a registered installation contractor to check the gas supply pressure and flow rate. If the problem persists, contact the Authorised Technical Services.
Why is the linen still damp after using my GIRBAU Dryer?
If the dried linen from your GIRBAU Dryer has a moisture level that is too high, it could be due to several reasons. First, the fabrics might have excessive residual moisture before drying, in which case you should adjust the spin process. Second, the drying time may be insufficient; try altering the program to increase the drying time. Finally, the temperature might be too low, so adjust the program to increase the temperature.
What to do if the burner won't ignite on my GIRBAU Dryer (gas version)?
If the burner of your GIRBAU Dryer (gas version) cannot be ignited, there are several potential causes. First, ensure that the manual gas flow valve is open. If it is, there might be an insufficient supply of gas. In this case, ask a Registered Installation Contractors to check the gas supply pressure and flow rate. If the problem persists, contact the Authorised Technical Services. Also, the gas ignition system may be defective or the ignition electrodes may be misplaced, in this case contact the Authorised Technical Services.
Why is the flame too orange in my GIRBAU ED260 (gas version)?
If the flame in your GIRBAU Dryer (gas version) appears too orange, it could be due to a faulty air intake filter. Try cleaning the filter. Alternatively, there might be a poor air/gas mixture. Check, and if necessary correct, the position of the venturi. If the problem persists, contact the Authorised Technical Services.
Why is there poor flame spread in my GIRBAU ED260 (gas version)?
If you're experiencing poor flame spread in your GIRBAU Dryer (gas version), it could be due to an insufficient supply of gas. Ask a Registered Installation Contractors to check the gas supply pressure and flow rate. If the problem persists, contact the Authorised Technical Services. It could also be caused by blocked burner holes, in this case contact the Authorised Technical Services.
What to do if my GIRBAU Dryer drum speed is incorrect?
If your GIRBAU Dryer has an incorrect drum speed, it may be due to an inverter breakdown or a fault in the drum rotation detector. In either case, contact the Authorised Technical Services.
Essential safety measures for installation, operation, and maintenance of Girbau equipment.
Explanation of hazard symbols and machine labels for safe operation.
Details the essential construction and functional features of the ED dryer series.
Describes gas burner operation, electric circuits, and steam heat exchangers.
Lists and explains the various protection, safety, and control features of the machine.
Lists directives and harmonised standards compliance for ED260-ED660 models.
Instructions for inspecting the dryer upon delivery and recommendations for proper storage.
Details safe methods for transporting the machine with or without its packaging.
Presents a comprehensive table of weights and dimensions for all ED dryer models.
Covers general requirements and minimum safety distances for installation site selection.
Guides on correctly positioning, levelling, and potentially anchoring the dryer.
Lists recommended environmental conditions and ventilation requirements for the machine.
Provides diagrams and measurements for work station heights for different ED models.
Presents a table of key technical specifications for all ED dryer models.
Details electrical connection specifications, protection devices, and wiring diagrams.
Provides specific heating data for EC, AGA, and ETL certified gas models.
Presents technical specifications and power consumption for steam-heated models.
Details nominal and reduced heating power and consumption for electric models.
Provides technical specifications for connecting the machine's exhaust ducting.
Details methods for connecting the machine to the power supply.
Explains procedures for connecting steam and gas supplies to the dryer.
Explains steps for changing gas type, including component adjustments.
Outlines specifications and procedures for installing the machine's exhaust duct.
Lists essential checks and preparations before the initial start-up of the dryer.
Procedures for analyzing combustion gases and adjusting the Venturi for gas-heated models.
Covers emergency stop, external start procedures, and available options like AFS.
Procedures for safely decommissioning, removing, and dismantling the dryer.
To Next Page
General
