To Next PageTo Next PageWhy is the dried linen moisture level too high in my GIRBAU Dryer?
If the dried linen has a high moisture level, it could be due to a few reasons: * There may be excessive residual moisture in the fabrics, so adjust the spin process. * The drying time may be insufficient, so alter the program to increase the drying time. * The temperature might be too low, so alter the program to increase the temperature.
What to do if the burner can not be ignited in my GIRBAU gas Dryer?
If the burner in your GIRBAU gas dryer won't ignite: * First, check if the manual gas flow valve is closed and open it. * If that's not the issue, a registered installation contractor should check the gas supply pressure and flow rate. If the problem persists, contact the Authorised Technical Services.
Why is the flame too orange in my GIRBAU gas Dryer?
An orange flame in your GIRBAU gas dryer could be caused by: * A faulty air intake filter, so clean the filter. * A poor air/gas mixture, so check, and if necessary correct, the position of the venturi. If the problem persists, contact the Authorised Technical Services.
What causes poor flame spread in my GIRBAU gas Dryer?
Poor flame spread in your GIRBAU gas dryer could be due to: * Insufficient gas supply, so ask a registered installation contractor to check the gas supply pressure and flow rate. If the problem persists, contact the Authorised Technical Services.
Why is the linen still damp after using my GIRBAU Dryer?
If the dried linen from your GIRBAU Dryer has a moisture level that is too high, it could be due to several reasons. First, the fabrics might have excessive residual moisture before drying, in which case you should adjust the spin process. Second, the drying time may be insufficient; try altering the program to increase the drying time. Finally, the temperature might be too low, so adjust the program to increase the temperature.
What to do if the burner won't ignite on my GIRBAU ED660 Dryer (gas version)?
If the burner of your GIRBAU Dryer (gas version) cannot be ignited, there are several potential causes. First, ensure that the manual gas flow valve is open. If it is, there might be an insufficient supply of gas. In this case, ask a Registered Installation Contractors to check the gas supply pressure and flow rate. If the problem persists, contact the Authorised Technical Services. Also, the gas ignition system may be defective or the ignition electrodes may be misplaced, in this case contact the Authorised Technical Services.
Why is the flame too orange in my GIRBAU ED660 Dryer (gas version)?
If the flame in your GIRBAU Dryer (gas version) appears too orange, it could be due to a faulty air intake filter. Try cleaning the filter. Alternatively, there might be a poor air/gas mixture. Check, and if necessary correct, the position of the venturi. If the problem persists, contact the Authorised Technical Services.
Why is there poor flame spread in my GIRBAU ED660 (gas version)?
If you're experiencing poor flame spread in your GIRBAU Dryer (gas version), it could be due to an insufficient supply of gas. Ask a Registered Installation Contractors to check the gas supply pressure and flow rate. If the problem persists, contact the Authorised Technical Services. It could also be caused by blocked burner holes, in this case contact the Authorised Technical Services.
What to do if my GIRBAU ED660 Dryer drum speed is incorrect?
If your GIRBAU Dryer has an incorrect drum speed, it may be due to an inverter breakdown or a fault in the drum rotation detector. In either case, contact the Authorised Technical Services.
General| Type | Tumble Dryer |
|---|---|
| Power Supply | Electric |
| Heating System | Electric |
| Control System | Electronic |
| Drum Material | Stainless Steel |
| Programs | Multiple drying programs |
Covers general warnings for fire, electrical shock, and proper handling of Girbau equipment.
Provides essential dos and don'ts, along with safety and control elements for machine use.
Details electrical connection requirements and necessary protection devices.
Specific heating, gas connection, and power data for certified gas models.
Details heating performance and electrical requirements for steam models.
Provides nominal and reduced heating power and consumption for electric models.
Includes wiring diagrams and installation measurements for connecting the machine.
Outlines electrical connection requirements, safety, and procedures for models with/without breaker switches.
Provides instructions and cautions for connecting the gas supply to the dryer.
Guides on modifying the machine for different gas types, including component changes and adjustments.
Procedure for analysing and adjusting combustion gases on gas-heated models.
