Glacier bay 1005877848

Questions and Answers

R
Robert HarrisAug 17, 2025
What to do if there is leaking or dripping from the spout of my Glacier Bay Bathroom Fixtures when the handle is closed?
- B
  bwellsAug 17, 2025
  If you notice leaking or dripping from the spout when the handle is closed, it could be due to a few reasons. The cartridge might not be properly installed, so try reinstalling it. Also, check to ensure the sealed washer on the cartridge is in place; if it's missing, replace the cartridge. Another possibility is that the bonnet nut isn't tightened enough. Use a wrench to retighten the bonnet nut sufficiently.
M
michael78Aug 20, 2025
Why is there no flow or low water flow in my Glacier Bay Bathroom Fixtures?
- T
  Tiffany McfarlandAug 20, 2025
  A lack of water flow or low water flow could be caused by several factors. Check if one or both water supplies are not turned on and ensure both water supply valves are in the 'on' position. Also, the stop valves might be turned off or not fully turned on; make sure to fully turn them on. Finally, the screen filter in the spray head could be blocked. To resolve this, turn off the water supply at the angle valve and unscrew the spray head from the spray hose, then clean the screen filter under running water.
J
Joshua BlevinsAug 23, 2025
What to do if water comes out of the tub spout and showerhead at the same time in my Glacier Bay Bathroom Fixtures?
- D
  David KellyAug 23, 2025
  If water is coming out of both the tub spout and showerhead simultaneously, it could be due to several reasons: * The pipe used between the valve and the tub spout is not 1/2 in. IPS, or the COPPER pipe is incorrect. Change the pipe to IPS or COPPER. * The distance between the valve and the showerhead is less than 48 in.. The distance from the showerhead and valve moved to at least 48 in.. * There is a restriction between the valve and the tub spout. Remove the tub spout, flush out any debris, and replace any undersized lines or fittings. * The valve is installed upside down. Remove the valve and reinstall it with the correct orientation.
K
Krystal GonzalezAug 26, 2025
Why is the handle hard to turn on my Glacier Bay Bathroom Fixtures?
- R
  Ricky CarterAug 26, 2025
  If the handle is hard to turn, the bonnet nut might be too tight. Try loosening the bonnet nut and reinstalling it, being careful not to overtighten it.
D
deborahmarshallAug 28, 2025
Why is there no hot water from my Glacier bay 1005877848 Kitchen & Bath Fixtures?
- S
  Shannon ReyesAug 28, 2025
  If you are not getting any hot water from your Glacier Bay Kitchen & Bath Fixtures, it could be due to a couple of reasons. Either the lines are reversed, or the cartridge is installed upside down, in which case you should rotate the cartridge 180°. Alternatively, the balance valve in the cartridge might be clogged with debris; try cleaning the bottom of the cartridge.
M
Michael AlvaradoAug 31, 2025
What to do if there is low water flow from Glacier bay 1005877848 Kitchen & Bath Fixtures?
- B
  brian08Aug 31, 2025
  If you're experiencing low or no water flow from your Glacier Bay Kitchen & Bath Fixtures, here are a few things to check: * Make sure both water supplies are fully turned on. * Ensure the stop valves are completely open. * Inspect the screen filter in the spray head for blockages; if blocked, turn off the water supply at the angle valve, unscrew the spray head from the spray hose, and clean the screen filter under running water.
S
Stephanie FranklinSep 2, 2025
How to fix a leaking Glacier bay 1005877848 spout?
- G
  Gerald ChaneySep 3, 2025
  If your Glacier Bay Kitchen & Bath Fixtures spout is leaking or dripping when the handle is closed, several issues could be the cause. First, make sure that the cartridge is properly installed. If the issue persists, check that the sealed washer on the cartridge is in place; if it's missing or damaged, replace the cartridge. Lastly, ensure the bonnet nut is sufficiently tightened using a wrench.
R
Ryan GuzmanSep 5, 2025
Why is the handle on my Glacier Bay Kitchen & Bath Fixtures hard to turn?
- L
  Lisa MullinsSep 5, 2025
  If the handle on your Glacier Bay Kitchen & Bath Fixtures is hard to turn, the bonnet nut might be too tight. Try loosening the bonnet nut and reinstalling it, being careful not to overtighten it this time.
P
Patricia Porter DVMSep 8, 2025
Why does water come out of the tub spout and showerhead at the same time in my Glacier Bay Kitchen & Bath Fixtures?
- M
  mrodriguezSep 8, 2025
  If water is coming out of both the tub spout and showerhead simultaneously in your Glacier Bay Kitchen & Bath Fixtures, it could be due to several reasons: * The pipe between the valve and tub spout is not 1/2 in. IPS, or the copper pipe is incorrect; in this case, change the pipe to IPS or copper. * The distance between the valve and the showerhead is less than 48 in.; the distance from the showerhead and valve moved to at least 48 in.. * There may be a restriction between the valve and the tub spout; remove the tub spout and flush out any debris, and/or replace any undersized lines or fittings. * The valve might be installed upside down; remove the valve and reinstall it with the correct orientation.
T
Timothy HunterSep 12, 2025
What to do if the handle cannot be installed on Glacier bay 1005877848?
- P
  Paula HernandezSep 12, 2025
  If you're having trouble installing the handle on your Glacier Bay Kitchen & Bath Fixtures, or if the handle rubs against the escutcheon, it's possible that the valve is installed too far back from the finished wall. Reinstall the valve (refer to Step 2 of the Installation section).