Godox MS200 - User Manual

Need help?

Do you have a question about the Godox MS200 and is the answer not in the manual?

Summary

Warning

General Safety Precautions

Safety instructions to prevent product damage, injury, and ensure proper usage.

Names of Parts

Body

Details the physical components and external features of the flash unit's body.

LCD Panel

Explains the various indicators and information displayed on the LCD panel.

Accessories

Lists the accessories that are included with the main product.

Separately Sold Accessories

Lists optional accessories that can be purchased to enhance product functionality.

Operations

Flash Preparation

Steps for setting up the flash unit, including installing covers and mounting.

Power Connection

Instructions on connecting the flash unit to an AC power source and turning it on.

Modeling Lamp

Explains modes (OFF, PROP, Percentage) and brightness adjustment for the modeling lamp.

Power Output Control

Details on using the select dial to adjust flash power output from 1/32 to 1/1.

Test Button

Describes how to use the test button to fire the flash or check its brightness.

Sync Triggering

Information on using the sync cord jack for synchronous firing with a camera shutter.

GR;CH Button

Explains how to adjust wireless group and channel settings using the GR/CH button.

Slave Trigger Model

Details S1 and S2 optic slave trigger modes for synchronized flash firing.

Buzz Function

Explains the sound function for ready flash notification after recharging.

Key Combination

Details button combinations for wireless transmission and factory reset.

Alarm Display

Lists and explains error codes (E0, E3) and troubleshooting advice.

Memory Function

Explains how the device remembers panel settings for 3 seconds after setup.

Over-Temperature Protection

Describes automatic flash shutdown and temperature alarm when overheating.

Wireless Control Function

Explains built-in 2.4G wireless transmission and control with X1/XT16 triggers.

Setting Communication Channel

Step-by-step guide to setting the wireless communication channel for the flash unit.

Setting Communication Group

Step-by-step guide to setting the wireless communication group for the flash unit.

Maintenance

Tube Replacement

Detailed steps for safely replacing the flash tube, including precautions.

General Maintenance Advice

Guidelines for device shutdown, cleaning, and general upkeep.

The Godox MS Series Compact Studio Flash is a lightweight, compact, and durable lighting solution designed for studio portraiture and e-commerce product photography. It is suitable for various applications including headshots, waist shots, certificate photography, and general product photography. The flash can also serve as high light, background light, or hair light in larger studios and workshops.

Function Description:

The MS series studio flash features a built-in Godox 2.4G wireless X system, allowing for remote control of flash power ratio, modeling lamp, and buzzer, as well as flash triggering, when used with optional X1, XT16, or FT-16 triggers. The flash provides precise output displayed on an LCD panel, with 50 steps of power adjustment from 1/32 to 1/1 (or 5.0 to 10.0). It offers outstanding output stability, with no more than 2% shifts under the same output. The anti-preflash function enables synchronization with cameras that have a one-preflash firing system. The device also includes an auto memory and recovery function for adjusted panel settings.

Important Technical Specifications:

The MS series comes in two models: MS200 and MS300.

Max Power (Ws): MS200 offers 200Ws, while MS300 offers 300Ws.
Guide Number (m ISO 100): MS200 has a guide number of 53, and MS300 has 58 (both with a highly effective reflector).
Color Temperature: 5600±200k.
Operating Voltage: AC110V-120V~60Hz or AC220-240V(50Hz).
Power Output Control: Adjustable from 5.0 to 10.0 (1/32 to 1/1).
Modeling Lamp (W): 150W.
Modeling Lamp Level: Adjustable from 5% to 100%.
Recycle Time: 0.1~1.3s (220V) / 0.1~1.8s (110V).
Triggering Method: Sync cord, Test button, Slave triggering, Wireless control port.
Flash Duration: 1/2000~1/800s.
Parameters Output from Sync Cord Jack: 5V.
Parameters Output from USB Port: 5V/200mA (only for Godox receiver).
Fuse: F8AL 250V.
Dimensions: Flash diameter 12.6cm, height of flash with handle 12.7cm, length of flash with lamp cover 28.3cm.
Net Weight: Approximately 2.6kg.

Usage Features:

Flash Preparation: Users need to install the modeling lamp and glass protection cover, then attach the flash unit to a light stand. The mounting bracket and direction adjusting handle allow for precise positioning.
Power Connection: Connect the flash to an AC power source using the provided power cord.
Modeling Lamp Control: The 150W modeling lamp can be set to OFF, PROP (power changes with flash power), or Percentage (manual brightness adjustment from 5% to 100%). It also features an auto-off function after 4 hours to prevent overheating. A long press of the modeling lamp button can toggle the function where the modeling lamp turns off when triggering the flash.
Power Output Control: The select dial allows free adjustment of power output from 1/32 to 1/1. The test button discharges power when output is adjusted from high to low.
Test Button: Used to fire the flash without taking a picture and to adjust flash brightness. Pressing the SET button and turning on the flash displays its version.
Sync Triggering: A 3.5mm sync cord jack allows synchronous firing with the camera shutter.
GR/CH Button: Short press to adjust the built-in wireless group (0 to F). Long press to adjust the built-in wireless channel (1 to 32).
Slave Trigger Model: Three modes are available:
- No optical control: Slave triggering is off.
- Optic S1 Secondary Unit Setting: In M manual flash mode, the flash fires synchronously with the main flash, ignoring pre-flashes.
- Optic S2 Secondary Unit Setting: In M manual flash mode, the flash ignores a single "preflash" from the main flash and fires in response to the second, actual flash.
Buzz Function: Provides an audible reminder when the flash is fully charged and ready.
Alarm Display: Indicates errors like "E0" (temperature sensor error) or "E3" (inner capacitance and voltage too high). If these alarms occur, the device should be sent for professional maintenance.
Memory Function: The device remembers panel settings 3 seconds after adjustment and restores them upon next startup.
Over-Temperature Protection: The flash automatically turns off its firing function and displays a blinking temperature alarm when its inner temperature is too high. Functions resume when the temperature drops below 50°C.
Wireless Control Function: The built-in 2.4G wireless transmission allows remote control with X1 and XT16 flash triggers. Synchronously pressing the GR/CH and S1/S2 buttons activates/deactivates wireless transmission. Channel IDs can be changed to prevent signal interference.

Maintenance Features:

Immediate Shutdown: The device should be shut down immediately if it works abnormally to diagnose the issue.
Impact Avoidance: Avoid sudden impacts, and the lamp should be regularly dedusted.
Normal Warming: It is normal for the lamp to warm up during use. Continuous flashes should be avoided if unnecessary.
Authorized Maintenance: Maintenance must be performed by an authorized department using original accessories.
User-Replaceable Parts: The flash tube and modeling lamp are user-replaceable and can be obtained from the manufacturer.
Warranty: The product, excluding consumables like flash tubes and modeling lamps, comes with a one-year warranty. Unauthorized service voids the warranty.
Damage/Wetting: If the product has failures or was wetted, it should not be used until repaired by a professional.
Power Disconnection: Disconnect the power when cleaning the flash or changing the flash tube/modeling lamp.
Specifications Changes: Changes to specifications or designs may not be reflected in the manual.
Tube Replacement: To replace the flash tube, shut down the power, remove the power cord, and wear insulated gloves. Loosen the iron wire, gently pull out the old tube, transfer the feet casing to the new tube, and carefully insert the new tube into the copper outlets, securing it with the iron wire.