IO137 27
LIGHTING INSTRUCTIONS
These instructions are also on the furnace
10. Turn on all electric power to the
talled, operated and
atically lights the burners. Do not try to
TO TURN OFF GAS TO APPLIANCE
3. Remove control access panel.
1. Set the thermostat to its lowest setting.
appliance if service is to be performed.
2. Turn off all electric power to the
or any other appliance.
other flammable vapors and liquids in the vicinity of this
FOR YOUR SAFETY
6. Move the gas control switch or knob
GAS CONTROL
KNOB
light the burners by hand.
5. Remove control access panel.
Do not store or use gasoline or
B14933-228
4. Move the gas control switch or knob
follow the instructions "To Turn Off Gas
to "OFF". Do not force.
5. Replace control access panel.
GAS CONTROL
SWITCH SHOWN
IN "ON" POSITION
To Appliance" and call your service
12. If the appliance will not operate,
11. Set the thermostat to the desired
technician or gas supplier.
setting.
appliance.
or other reproductive
harm.
Fiberglass insulation
fiberglass insulation.
known by the State of
This product contains
California to cause
cancer.
contains a chemical
expose you to subst-
maintained in accord-
ance with the manuf-
acturer's instructions,
known to the State of
tion which can cause
ances in fuel combus-
cancer, birth defects
death or serious illn-
California to cause
ess and which are
this product could
OPERATING INSTRUCTIONS
1. STOP! Read the safety information
2. Set the thermostat to lowest setting.
3. Turn off all electric power to the appl-
4. This appliance is equipped with an
automatic ignition system which autom-
A. This appliance does not have a pilot. It
is equipped with an ignition device which
automatically lights the burners. Do not
B. BEFORE OPERATING smell around
the appliance area for gas. Be sure to
smell next to the floor because some gas
is heavier than air and will settle on the
from a neighbor's phone. Follow
do not use any telephone in your
Do not touch any electric switch;
Do not try to light any appliance.
WHAT TO DO IF YOU SMELL GAS
iance.
above on this label.
the gas suppliers instructions.
try to light the burners by hand.
building.
Immediately call your supplier
floor.
erty damage. Refer to
call a qualified service technician.
will not operate, don't try to repair it,
gas. If you then smell gas, STOP!
gas, go to the next step.
9. Replace control access panel.
8. Move the gas control switch or knob
above on this label. If you don't smell
Follow "B" in the safety information
7. Wait five (5) minutes to clear out any
the control system and any gas control
the appliance and to replace any part of
a qualified service technician to inspect
has been under water. Immediately call
D. Do not use this appliance if any part
tools. If the gas control switch or knob
control switch or knob. Never use
C. Use only your hand to move the gas
which has been under water.
installed in accordan-
If not ins-
codes follow the
ce with the manufac-
National Fuel Gas
Code, ANSI Z223.1.
WARNING:
the absence of local
and local codes. In
turers instructions
information consult a
this furnace. For ass-
qualified installer, ser-
manual provided with
the user's information
This furnace must be
vice agency or the
gas supplier.
istance or additional
If you do not follow these instructions exactly,
a fire or explosion may result causing property
If you cannot reach your gas supplier,
damage, personal injury or loss of life.
call the fire department.
installation, adjustm-
ent, alteration, service
cause injury or prop-
Improper
or maintenance can
WARNING:
For indoor installation.
FOR YOUR SAFETY READ BEFORE OPERATING
a fire or explosion.
Force or attempted repair may result in
to "OFF".
to "ON".
PGB & PGJ
For outdoor install-
ation only.
SWITCH SHOWN
IN "ON" POSITION
GAS CONTROL
To Next Page
Loading...
