Goodman GMVS960805CU AA - System Operation; Safety


6

Please adhere to the following warnings and cautions when
installing, adjusting, altering, servicing, or operating the
furnace.

 REVE ERS IJUR R E UE IMRER ISI
JUSME ERISERVIE R MIEEREER IS
MU

R II SS ISE R IRMI SU
QUIIE ISER SERVIE ER E S SUIER



REVE SSIE RER ME ERS IJUR R E
UE EERI SK E URE MUS EE RE
E EERI MES RMWER

Discharge your body’s static electricity before touching
unit. An electrostatic discharge can adversely a󰀨ect electrical
components.
Use the following precautions during furnace installation
and servicing to protect the integrated control module from
damage. By putting the furnace, the control, and the person
at the same electrostatic potential, these steps will help
avoid exposing the integrated control module to electrostatic
discharge. This procedure is applicable to both installed and
uninstalled (ungrounded) furnaces.
1. Disconnect all power to the furnace. Do not touch the
integrated control module or any wire connected to the
control prior to discharging your body’s electrostatic
charge to ground.
2. Firmly touch a clean, unpainted, metal surface of the
furnace near the control. Any tools held in a person’s
hand during grounding will be discharged.
3. Service integrated control module or connecting wiring
following the discharge process in Step 2. Use caution
not to recharge your body with static electricity; (i.e., do
not move or shu󰀪e your feet, do not touch ungrounded
objects, etc.). If you come in contact with an ungrounded
object, repeat Step 2 before touching control or wires.
4. Discharge any static electricity from your body to ground
before removing a new control from its container. Follow
Steps 1 through 3 if installing the control on a furnace.
Return any old or new controls to their containers before
touching any ungrounded object.

This product is designed for use as a residential home gas
furnace. It is  designed or certied for use in mobile home,
trailer, or recreational vehicle applications.
In the U.S.A., this furnace can be used in the following non-industrial
commercial applications: Schools, O󰀩ce buildings, Churches, Retail
stores, Nursing homes, Hotels/motels, Common or o󰀩ce areas. In
all applications, the furnace must be installed per the installation
instructions.
Goodman
®
brand GMVS96*U and Amana
®
brand AMVS96*U
furnaces are ETL certied. All *MVS96*U furnaces are built
for use with Natural gas only & may not be converted for use
with LP gas.
Goodman
®
brand GMVS96*U and Amana
®
brand AMVS96*U
high e󰀩ciency furnaces are dual certied. Dual certication
means that the combustion air inlet pipe is optional and the
furnace can be vented as a:
• Non-direct vent (single pipe) central forced air furnace
in which combustion air is taken from the installation
area or from air ducted from the outside or,
• Direct vent (dual pipe) central forced air furnace in
which all combustion air supplied directly to the furnace
burners through a special air intake system outlined in
this manual and the installation instructions.
To ensure proper installation, operation and servicing,
thoroughly read the installation and service manuals
for specics pertaining to the installation, servicing and
application of this product.


SSIE RER ME ERS IJUR R E UE IRE
EXSI SMKE SESI EERI SK RR
MXIE M RESURMIMRER ISIREIR ERI
R MIEE  IS RU


 REVE RER ME ERS IJUR R E UE IRE
 IS IS URE I MIE ME RIER R REREI
VEIE
To ensure proper furnace operation, install, operate, maintain
and service the furnace in accordance with the installation,
operation and service instructions, all local building codes
and ordinances. In their absence, follow the latest edition of
the National Fuel Gas Code (NFPA 54/ANSI Z223.1), and/or
CAN/CGA B149 Installation Codes, local plumbing or waste
water codes, and other applicable codes.

All *MVS96*U furnaces must have an EMI Filter installed.
Early production furnaces will require the EMI lter to be
eld installed at the time of furnace installation as furnaces
are shipped without this component. The kit (EMIULN-1) is
available from your furnace distributor at no cost.
The purpose of the EMI Filter is to reduce electromagnetic
interference between the furnace and other electrical devices.