Graco 254986 User Manual (English)

Other manuals for Graco 254986

Operation18 pages

Repair Manual32 pages

Questions and Answers:

J
Jason CunninghamAug 20, 2025
Why won't my Graco 254986 Paint Sprayer run?
- A
  Angela AndersonAug 20, 2025
  If your Graco Paint Sprayer won't run, there could be several reasons: * The power switch might not be on. Turn the switch on. * There might be no power at the wall outlet. Check the outlet by plugging in another appliance. If that appliance doesn't work, try a different outlet. * You might be using the wrong size generator. Use a 3500 watt or larger generator. * The breaker might have tripped. Reset the breaker.
A
Anthony WaltersAug 22, 2025
Why is material running out of the bottom of my Graco 254986 Paint Sprayer?
- M
  Maurice CombsAug 22, 2025
  If material is running out of the bottom of your Graco Paint Sprayer, the cause might be: * A worn-out pump hose. Replace the hose. * Loose fittings. Check and retighten all fittings.
M
Matthew RitterAug 25, 2025
Why is my Graco Paint Sprayer having intermittent flow or sputtering?
- T
  turnerchristinaAug 25, 2025
  If your Graco Paint Sprayer is experiencing intermittent flow or sputtering, check if: * The hopper connection is not tight. Inspect the gasket and tighten the connection. * There is debris in the system. Clean the system.
M
Mark DavisAug 26, 2025
Why is fluid leaking at the Flow Adjustment Nut on my Graco Paint Sprayer?
- E
  enewmanAug 26, 2025
  If you notice fluid leaking at the Flow Adjustment Nut of your Graco Paint Sprayer, it's likely due to a damaged seal. Replace the seal.
M
Miguel JohnsonAug 28, 2025
Why is fluid leaking out of either plug on my Graco Paint Sprayer?
- T
  Tyler JohnsonAug 28, 2025
  If fluid is leaking out of either plug on your Graco Paint Sprayer, it could be due to: * Missing or damaged o-rings. Replace the o-rings. * A damaged gun. Replace the gun.
J
Jesse ThorntonAug 29, 2025
Why is my Graco 254986 Paint Sprayer having intermittent flow/sputtering?
- L
  Laura ThomasAug 30, 2025
  If you're experiencing intermittent flow or sputtering with your Graco Paint Sprayer, check the hopper connection and tighten it, ensuring the gasket is in place. Additionally, clean the system to remove any debris.
L
Lynn CooperAug 31, 2025
What to do if my Graco 254986 pump won’t pump material?
- C
  Craig LaraSep 1, 2025
  If the pump on your Graco Paint Sprayer isn’t pumping material, consider the following: * There might be an air lock. Open the air valve on the gun. * The selector switch may be in the wrong position. Move it to the correct position for your application. * The mix could be too thick. Add water to thin the material, using the Material Thickness Gauge. * Fittings might be loose. Check and retighten all fittings. * The gun could be plugged. Remove the gun from the hose and clean it. * The pump hose might be worn out. Replace the hose, ideally once a year. * The pump could be cold. Move it to a warm room to warm up, or run hot water through the sprayer.
S
Sarah MccallSep 2, 2025
What to do if my Graco 254986 gun will not shut off?
- C
  castroyvetteSep 2, 2025
  If the gun on your Graco Paint Sprayer will not shut off, it could be due to: * A worn nozzle or needle. Replace the worn parts. * Debris in the needle passage. Clean it.
M
morrowbradSep 4, 2025
Why is the application speed slow on my Graco Paint Sprayer?
- W
  William NelsonSep 4, 2025
  If your Graco Paint Sprayer's application speed is slow, thin the material if it's too thick. Partially close the gun air valve to reduce airflow. Check for a kinked hose and unkink it. Adjust the flow with the flow adjustment nut. Unplug other items from the circuit. Replace the pump hose if it's worn.
S
Scott CastroSep 6, 2025
Why is there no air coming from my Graco 254986 compressor?
- J
  Jesus MartinezSep 6, 2025
  If your Graco Paint Sprayer has no air coming from the compressor, check these potential causes: * The gun air valve might be closed. Open the gun air valve. * There could be low voltage. Check the extension cord length and gauge, and replace it if it doesn't meet recommendations. * The gun needle might be plugged. Clean the needle and try again. * The compressor might be worn. Replace the compressor, or contact a qualified Graco Service Center. * The lines might not be connected. Check all quick disconnect connections to the gun and hoses. * The hose could be damaged. Replace the hose.