Graco BULLDOG E Series - ADJUST-A-STROKE Pump Variation Chart; ADJUST-A-STROKE Pump Specifications

21307-050
ADJUST-A-STROKE Pump V ariation Chart
Cylinder Material Piston Type Packing Material Reference to Air Motor Displacement Connecting
Tie Rods Tube
Elbow Std. Pump No. Pump Rod

Dimension Displacement Pump
20:1 King
CST L & U DB 207–567 23.50” (596.9 mm) 952–356 207–655 168–212 620–059 None None
SST R DB 951–803 22.125” (561.9 mm) 952–356 902–169 620–065 620–064 None None
CST T & U PP 222–248 32.50” (825.5 mm) 952–356 204–641 168–212 620–013 None None
SD T PP 220–648 32.50” (825.5 mm) 952–356 207–242 620–065 620–063 None None
SD T & U PP 222–539 32.50” (825.5 mm) 207–647 222–638 620–005 620–063 None None
45:1 King
CST L & U DB 218–335 21.0” (533.4 mm) 952–356 217–527 168–212 620–060 None None
CST L & U DB 221–063 32.375” (822.3 mm) 952–356 217–527 168–212 620–061 170–094 None
45:1 King
CST L & U DB 218–335 21.0” (533.4 mm) 952–356 217–527 168–212 620–060 None None
CST L & U DB 221–063 32.375” (822.3 mm) 952–356 217–527 168–212 620–061 170–094 None
55:1 King
CST U PP 217–566 32.75” (831.8 mm) 952–356 217–201 168–212 620–013 None None
SD T & U PP 222–545 32.75” (831.8 mm) 207–647 222–639 168–212 620–013 None None
KEY:
Packing Material Piston T ype Cylinder Material
L Leather T PTFE DB Double Ball C ST N itrated Carbon Steel
N Neoprene U UHMWPE DP Double Poppet SST Stainless Steel
R Rubber PP Priming Piston SD Severe Duty
ADJUST-A-STROKE Pump Specifications
Pump
Air Motor Diameter
Inch (mm)
Piston Stroke Range
Inch (mm)
Pressure Pis-
ton
Ratio Type
Approximate
Per Cycle Range
Fluid Oz (liter)
37.5 to 100% 37.5 to 100%
Senator
15:1 SD PP 2.4 – 6.4 (0.07 – 0.19)
5.5 (139.7) 1.6 – 4.25 (40.6 – 107.9) 25:1 SD PP 2.4 – 6.4 (0.07 – 0.19)
Bulldog
5:1 DB** 12.0 – 32.0 (0.36 – 0.95)
5:1 DP** 12.0 – 32.0 (0.36 – 0.95)
10:1 SD DB** 6.8 – 18.0 (0.20 – 0.53)
7 (177.8) 1.6 – 4.25 (40.6 – 107–9) 10:1 SD PP** 6.8 – 18.0 (0.20 – 0.53)
20:1 SD DB 3.0 – 8.0 (0.09 – 0.24)
25:1 SD PP 3.0 – 8.0 (0.09 – 0.24)
30:1 SD DB 2.4 – 6.4 (0.07 – 0.19)
40:1 SD PP 1.7 – 4.6 (0.05 – 0.14)
King
20:1 SD DB** 6.8 – 18.0 (0.20 – 0.53)
10 (254) 1.6 – 4.25 (40.6 – 107.9) 20:1 SD PP 6.8 – 18.0 (0.20 – 0.53)
45:1 SD DB 3.2 – 8.5 (0.10 – 0.25)
55:1 SD PP 2.4 – 6.4 (0.07 – 0.19)
KEY:
DB
Double Ball
DP Double Poppet
PP Priming Piston
SD Severe Duty (standard)
** A vailable in Stainless Steel
NOTE: Only immersed, inductor or ram-mounted
pumps are to be used for metering.