To Next PageTo Next PageWhy is there fluid in the exhaust air of my Graco Water Pump?
Fluid in the exhaust air indicates that the diaphragm has ruptured or the diaphragm plate is loose. To resolve this, replace the diaphragm or tighten the diaphragm plate. Consult the standard or overmolded repair procedure for detailed instructions.
Why does my Graco SaniForce 2150 Water Pump operate erratically?
Erratic operation of your Graco Water Pump can stem from several causes. It could be due to a clogged suction line, sticky or leaking check balls or flap valves, flap valves installed upside-down, a ruptured diaphragm, or a restricted exhaust. To address this: * Inspect and clear any clogs in the suction line. * Clean or replace sticky or leaking check balls or flap valves. * Ensure flap valves are installed correctly with the text side facing the seat. * Replace a ruptured diaphragm, referring to the standard or overmolded repair procedure. * Remove any restrictions in the exhaust.
How to fix air bubbles in fluid from Graco SaniForce 2150?
If you notice air bubbles in the fluid, check for a loose suction line and tighten it. Also, a ruptured diaphragm could be the cause, requiring replacement following the standard or overmolded repair procedure. Additionally, inspect the inlet manifold for looseness, damaged seals, or gaskets; tighten the manifold clamps or replace any damaged gaskets or seating components.
Why is my Graco Water Pump leaking air externally?
External air leaks from your Graco Water Pump can be attributed to a loose air valve cover, damaged air valve or air cover gaskets, or loose air cover clamps. Ensure the air valve cover screws and air cover clamps are tightened. Inspect the air valve gasket and air cover gasket for damage and replace if necessary.
What causes excessive air exhaust at stall in a Graco SaniForce 2150 Water Pump?
Excessive air exhaust at stall in your Graco Water Pump may be due to a worn air valve block, plate, pilot block, u-cups, or pilot pin o-rings, or worn shaft seals. Repair or replace the worn components. If the shaft seals are worn, replace them, consulting the standard or overmolded repair procedure.
What to do if there's a leak in the inlet or outlet sanitary fitting of my Graco Water Pump?
A leak in the inlet or outlet sanitary fitting could be due to a loose sanitary clamp, a damaged or worn gasket, or misalignment of the inlet/outlet hose or pipe. To fix this, first tighten the clamp. If the gasket is damaged or worn, replace it. If there is misalignment, use flexible hoses at the pump inlet and outlet.
Why is my Graco SaniForce 2150 Water Pump leaking fluid externally from the ball check valves?
Fluid leaking externally from the ball check valves is often caused by loose manifolds, a damaged seal between the manifold and fluid cover, or damaged gaskets. Try tightening the manifold clamps or replacing the seats or clamps to resolve the issue.
Why does my Graco SaniForce 2150 cycle at stall or fail to hold pressure?
If your pump cycles at stall or fails to hold pressure at stall, the checks or seats are likely worn. Replace them to resolve this issue.
What causes chattering in my Graco SaniForce 2150?
Chattering can occur when check valve balls are not seating properly or cleanly due to an imbalance between the fluid inlet and outlet line sizing. This noise is more noticeable with light viscosity fluids. To fix this, reduce the size or diameter of the inlet line relative to the outlet line, ensuring the outlet line size does not exceed the pump size.
Why don't the manifolds fit for installation onto fluid covers of my Graco Water Pump?
If the manifolds do not fit onto the fluid covers, it may be due to the use of incorrect air cover gaskets, resulting in misalignment. Install the correct air cover gaskets for the type of diaphragms in use. Refer to the Parts list for the correct gasket.
General| Model | SaniForce 2150 |
|---|---|
| Type | Diaphragm Pump |
| Air Inlet Size | 1/2" NPT |
| Wetted Parts | Stainless Steel, PTFE |
| Material | Stainless Steel |
| Power Source | Pneumatic |
| Engine | Air-powered |
