Graco TexSpray RTX 750

Other manuals for Graco TexSpray RTX 750

Questions and Answers

B
brownfrankAug 18, 2025
Why won't my Graco TexSpray RTX 750 run?
- G
  Gregory KellyAug 18, 2025
  If your Graco Paint Sprayer won’t run, there might be several reasons. First, ensure the power switch is turned on. Then, check the wall outlet by plugging in another appliance; if it doesn't work, try a different outlet. Also, verify you're using a 3500 watt or larger generator. Try unplugging other items from the same circuit. If using an extension cord, make sure it's not too long or the wrong gauge. Finally, check if the breaker has tripped and reset it if necessary.
M
Mark BushAug 20, 2025
Why is material running out of the bottom of my Graco Paint Sprayer?
- C
  christopherelliottAug 20, 2025
  If material runs out of the bottom of your Graco Paint Sprayer, it could be due to a worn pump hose, so replace it. Alternatively, check all fittings and retighten them if they are loose.
D
Danny EvansAug 23, 2025
What to do if my Graco TexSpray RTX 750 Paint Sprayer won’t run?
- N
  Norma ParrishAug 23, 2025
  If your Graco Paint Sprayer won’t run, first ensure the power switch is on. Then, check the wall outlet by plugging in another appliance. If it still doesn't work, try a different outlet. Also, make sure you're using a 3500 watt or larger generator. Unplug other items from the circuit to reduce the load. Verify that the extension cord isn't too long or of the wrong gauge, and reset the breaker if it has tripped.
C
Craig ColemanAug 26, 2025
Why is the application speed of my Graco TexSpray RTX 750 slow?
- A
  Anthony GravesAug 26, 2025
  If your Graco Paint Sprayer's application speed is slow, it could be due to several factors. The material might be too thick, so try thinning it. The nozzle could be too small, consider changing to a larger size. Too much air being used? Partially close the gun air valve to reduce airflow. If you have the RTX 1000 model, the flow control might be set too low, so increase the flow control setting. Check the pump hose, if it's worn, replace it. Also, the gun might be plugged or dirty, so relieve pressure and clean it. Make sure the hose isn't kinked, and check the gun adjustment, increasing the flow adjustment with the flow adjustment nut if it's set too low.
B
Brent MolinaAug 27, 2025
What to do if my Graco TexSpray RTX 750 pump won’t pump material?
- L
  Lee TaylorAug 27, 2025
  If your Graco Paint Sprayer pump won’t pump material, first check for an air lock and open the air valve on the gun. Ensure the selector switch is in the correct position for your application. If the mix is too thick, add water to thin the material. Check and retighten all fittings if they are loose. If the gun is plugged, relieve pressure and clean it. Consider replacing the hose if it's worn out, typically every 2000-2500 gallons. If the pump is cold, move it to a warm room or run hot water through the sprayer to warm it up.
B
Barbara GallegosAug 30, 2025
Why is my Graco Paint Sprayer experiencing intermittent flow or sputtering?
- A
  Amy PetersonAug 30, 2025
  If you experience intermittent flow or sputtering with your Graco Paint Sprayer, check the hopper connection to ensure it's tight and the gasket is in place. Tighten the connection if necessary. Also, check for any debris in the system and clean it.
W
Wesley SantiagoSep 1, 2025
Why won’t the gun on my Graco Paint Sprayer shut off?
- S
  Steven ThompsonSep 1, 2025
  If the gun on your Graco Paint Sprayer will not shut off, relieve the pressure and replace worn parts if the nozzle or needle are worn. Also, relieve the pressure and clean the needle passage if there's debris in it.
T
Taylor LopezSep 3, 2025
Why is there no air coming from the compressor of my Graco TexSpray RTX 750 Paint Sprayer?
- B
  Brian WoodsSep 3, 2025
  If there's no air from the compressor of your Graco Paint Sprayer, start by opening the gun air valve. Check the extension cord length and gauge, and replace it if it doesn't meet the recommendations. Clean the needle and retry if the gun needle is plugged. If the compressor is worn, contact a qualified Graco Service Center to replace it. Ensure all quick disconnect connections to the gun and hoses are properly connected. Replace the hose if it's damaged.
D
Debra BrownSep 6, 2025
What to do if the quick disconnect on my Graco TexSpray RTX 750 does not stay connected?
- A
  Ashley HutchinsonSep 6, 2025
  If the quick disconnect on your Graco Paint Sprayer does not stay connected, the fitting might be dirty or corroded. Clean it thoroughly, soak it in oil, and apply a few drops of light oil.
H
Heather LopezSep 8, 2025
Why is fluid leaking at the Flow Adjustment Nut on my Graco Paint Sprayer?
- N
  nicolesmithSep 8, 2025
  If fluid is leaking at the Flow Adjustment Nut of your Graco Paint Sprayer, the seal might be damaged. Relieve the pressure and replace the seal.